Keyscan CA250B Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 140

background image

Keyscan Inc. – Technical Guide (PC109x - 04.15)

125

Appendix E – Accessibility
HC Relay

The optional accessibility HC relay is designed to connect with an accessibility operator that mechanically
opens and closes a door. Presenting a card with the accessibility designation at a valid door pulses a
designated accessibility HC output relay. The accessibility HC output relay pulses the accessibility operator and
the system monitors the door contact based on the accessibility door held open time set in the Client software.
To use the accessibility HC relay option on CA4500B and CA8500B control boards, an additional OCB-8 is
required.

Accessibility HC Output Relays

Ensure that the accessibility HC output relay matches the door output as indicated below.

Table 26 – Accessibility HC Relay/ Door Assignment

Control Board/OCB-
8

Door # /HC Relay #

Ribbon Cable Connection OCB-8 to Control
Board

CA250B/OCB-8

Door 1/HC relay 5
Door 2/HC relay 6
Relay 7 and 8 reserved for Pre-
alert.

Connect ribbon from OCB-8 to control 1 on CA250B

CA4500B/OCB-8
(optional)

Door 1/HC relay 1
Door 2/HC relay 2
Door 3/HC relay 3
Door 4/HC relay 4
Relays 5 to 8 not used.

Connect ribbon on OCB-8 to control 4 on CA4500B.

CA8500B/OCB-8
(optional)

Door 1/HC relay 1
Door 2/HC relay 2
Door 3/HC relay 3
Door 4/HC relay 4
Door 5/HC relay 5
Door 6/HC relay 6
Door 7/HC relay 7
Door 8/HC relay 8

Connect ribbon on OCB-8 to control 4 on CA8500B.

«
...
123
124
125
126
127
...
»

Содержание CA250B













































































































































Отзывы:

Нет отзывов

Похожие инструкции для CA250B

Бренд: Radio Shack Страницы: 52

Бренд: Fancom Страницы: 31

Бренд: 3M Страницы: 90

Бренд: Federal Signal Corporation Страницы: 34

Бренд: Harsco Industrial Страницы: 57

Бренд: Jedia Страницы: 12

Бренд: JED Micro Страницы: 10

Бренд: JCM Technologies Страницы: 2

Бренд: K'Nex Education Страницы: 56

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Бренд: Nabco Страницы: 35

Бренд: Omega Страницы: 56

Бренд: Omega Страницы: 2

TEMP2000 Series

Бренд: Samwontech Страницы: 91

Бренд: Warren rupp Страницы: 18

Бренд: Yamaha Страницы: 100

Бренд: VAT Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды