background image

5

DEFINITIONS

INPUT

 - INPUT; This section of the program menu assigns the type of input the unit will be using (4-20 mA, 0-5 V, 0-10 V,

1-5 V, Linear or square root extraction).

I 4-20

 - I 4-20; This sets the unit for a current input of 4 to 20 mA.

E 1-5

 - E 1-5; This sets the unit for a voltage input of 1 to 5 volts.

E 0-5

 - E 0-5; This sets the unit for a voltage input of 0 to 5 volts.

E 0-10

 - E 0-10; This sets the unit for a voltage input of 0 to 10 volts. (0-20 mA input is available using this setting and the

current (I) input pin 4)

RELAYS

 - RELAYS; This section of the program menu sets the control output variables (relays & open collector).

HYS A

- HYSTERESIS FOR OUTPUT A; This value is the number of units below Preset A that the output will remain "ON".

EXAMPLE: Preset A set at 100, Hys set at 10.  Output A will activate (turn on) when the rate equals 100; Output
A will deactivate (turn off) when the rate falls below 90 (10 below Preset A)

HYS B

- HYSTERESIS FOR OUTPUT B; Same as HYS A.

LOC

 - LOCK; This section of the program menu sets up the lockout type and code. (to lock or unlock, press the "A" key

when in run mode.  see pg.10)

LC ALL

 - LOCK ALL; When this is selected the lockout will lock the program as well as the Presets and reset button.  The

presets can be viewed but not changed.

LC PG

 - LOCK PROGRAM; When this is selected the lockout will lock only the program.  The Reset can be activated and

the presets can be viewed and changed.

CODE

 - CODE; This is a 5-digit code which will be used to lock and unlock the front panel.

SETUP

 - SETUP; This section of the program menu sets up the operating variables.

DECLOC

 - DECIMAL LOCATION; This allows the user to program a decimal point.

SET LO

 - SET LOW; This is the display value (-9999 to 49999) for the lowest input (0 or 1 Volts; 4 mA).

 (i.e. 4 mA = -10 

°

)

SET HI

 - SET HIGH; This is the display value (-9999 to 49999) for the highest input (5 or 10 Volts; 20 mA).  (i.e. 20 mA =

100 

°

)

LO CUT

 - LOW CUT-OFF; This is the lowest display value (-9999 to 49999) to be recognized.  All readings below this

value will assume the "set lo" value, even if the "set lo" is higher than the "set hi" value..

NOR

 - NORMALIZING FACTOR; This is an averaging factor (00.0 to 99.9).  Higher settings provide more normalizing

(averaging) for a more stable display.  Derived from the equation:

(OLD DATA x "NOR" + NEW DATA)

("NOR" + 1)

opt

 - OPTIONS; This section of the program menu is for setting up optional features (analog out, RS232/422 serial

communications).

out lo

 - OUT LOW; The displayed value (-9999 to 49999) at which the unit will output 4 mA (-10

°

 = 4 mA out).

Содержание INTELLECT-69PM2























Отзывы: