6
DEFINITIONS
Save Total
: (Save Total) Press the E key while the unit is running to save the total value. The display will show
"
save total
" for a few seconds. This is a very useful "scratch pad" to save and restore total when replacing
the battery(ies)
ent Code
: (enter code) This prompt will only appear if the panel lock is ON. Press the
↑
key to increment each digit.
Press the
←
key to step to the next digit to the left. Press the E key to enter the 5 digit code. If the entered
code is correct, the display will advance to the next menu prompt (CLr tot). If incorrect, the display will return
to the run mode.
Clr tot
: (clear total) Clears (resets) the totalizer. Press the E key to clear the total and return to the run mode. Press
the M key to skip and advance to the next menu selection.
fdeC
: (factor decimal) Sets the decimal location for the factor. This location is restricted to 3 places (99.999). The use
of this decimal automatically limits the number of decimal locations allowable in the rate and total to acceptable
ranges. Press the
←
key to move the decimal. Press the E key to select the displayed decimal location.
NOTE:
For best performance and resolution choose as many decimal places as possible in the K-Factor.
Example: Enter a K-Factor of 1 as 1.000.
faC lInear
/
20poInt
: (factor type) This prompt will only appear if the unit is ordered with the 20 point linearization op-
tion. The
20 poInt
linearization selection is recommended for flow meters whose K-factors change with different
flow rates. This selection allows users to enter up to 20 different frequencies with 20 corresponding K-factors for
different flow rates. The
lInear
setting is used for flow meters whose output is linear over its' entire operating
flow range. Press the
↑
key to step to the desired choice. Press the E key to enter the displayed factor type.
No
/
yes set Pnts
: (set 20 point?) This prompt allows the user to skip the 20 point setup routine. Select
yes
for
initial setup or to change the present 20 point values. Select
No
to skip and keep the existing values.
faC
: (factor) This prompt appears on all units with linear inputs. The Factor is the number of pulses per unit volume
for the flow sensor. The pulses/unit volume is implied by the totalizer descriptor when a descriptor is used. The
implied units for the Factor are then as follows:
Standard "D" Option
GAL pulses/gallon
GAL pulses/gallon
LIT
pulses/liter
BBL
pulses/BBL
FT3
pulses/ft3
MCF pulses/MCF
M3 pulses/M3
M3 pulses/M3
Factors from 0.0001 to 99999999 may be used. A "0" value for the factor is not allowed and the unit will default
to "1" in LSD if a "0" entry is attempted . The factor is displayed on the subsidiary (lower) display. Press the
↑
key to increment each digit. Press the
←
key to step to the next digit to the left. Press the E key to enter the
displayed factor.
fr#
: (frequency for point #) This prompt will only appear when 20 point selected. It sets the frequency for each of
the 20 points (#). Press the
↑
key to increment each digit. Press the
←
key to step to the next digit to the left.
Press the E key to enter the desired frequency for point #.
faC#
: (factor for point #) This prompt will only appear when 20 point selected. It sets the factor for each of the 20
points (#). Press the
↑
key to increment each digit. Press the
←
key to step to the next digit to the left. Press
the E key to enter the desired factor for point #.
NOTE: The display will advance to the next point (Fr#) after each entry of the Fr & Fac until all 20 points are com-
plete. entering a 0 in the Fr or fac setting will advance the display to the next menu prompt (tdec).
