5
TK-785
REALIGNMENT
5. PC Mode
5-1. Preface
The TK-785 transceiver is programmed by using a per-
sonal computer, programming interface (KPG-46) and pro-
gramming software (KPG-62D).
The programming software can be used with an IBM PC
or compatible. Figure 1 shows the setup of an IBM PC for
programming.
5-2. Connection Procedure
1. Connect the TK-785 to the personal computer with the
interface cable.
2. When the Power switch on, user mode can be entered
immediately. When PC sends command the radio enter
PC mode, and “PROGRAM” is displayed on the LCD.
When data transmitting from transceiver, the red LED is
blinking.
When data receiving to transceiver, the green LED is
blinking.
Notes :
• The data stored in the personal computer must match
model type, when it is written into the flash memory.
• Change the TK-785 to PC mode, then attach the interface
cable.
5-3. KPG-46 Description
(PC programming interface cable : Option)
The KPG-46 is required to interface the TK-785 to the
computer. It has a circuit in its D-subconnector (25-pin) case
that converts the RS-232C logic level to the TTL level.
The KPG-46 connects the modular microphone jack of
the TK-785 to the computers RS-232C serial port.
5-4. Programming Software KPG-62D Description
The KPG-62D is the programming software for the trans-
ceiver supplied on two 3.5" floppy disks. This software runs
under MS-Windows 95/98 on an IBM-PC or compatible ma-
chine.
The data can be input to or read from the transceiver and
edited on the screen. The programmed or edited data can
be printed out. It is also possible to tune the transceiver.
We recommend that install the KPG-62D for example to
hard disk first then use it.
5-5. Programming With IBM PC
If data is transferred to the transceiver from an IBM PC
with the KPG-62D, the destination data (basic radio informa-
tion) for each set can be modified. Normally, it is not neces-
sary to modify the destination data because their values are
determined automatically when the frequency range (fre-
quency type) is set.
The values should be modified only if necessary.
Data can be programmed into the flash memory in RS-
232C format via the modular microphone jack.
KPG-46
IBM-PC
KPG-62D
TK-785
Fig. 1
6. Firmware Programming Mode
6-1. Preface
Flash memory is mounted on the TK-785. This allows the
TK-785 to be upgraded when new features are released in
the future. (For details on how to obtain the firmware, con-
tact Customer Service.)
6-2. Connection Procedure
Connect the TK-785 to the personal computer (IBM PC or
compatible) with the interface cable (KPG-46). (Connection
is the same as in the PC Mode.)
6-3. Programming
1. Start up the programming software (Fpro. exe).
2. Set the communications speed (normally, 57600 bps)
and communications port in the configuration item.
3. Set the firmware to be updated by File name item.
4. Turn the TK-785 Power ON with the [A] switch held
down. Hold the switch down until the display changes to
“PROG 57600”. When “PROG 57600” appears, release
your finger from the switch.
5. Check the connection between the TK-785 and the per-
sonal computer, and make sure that the TK-785 is in the
Program mode.
6. Press write button in the window. A window opens on
the display to indicate progress of writing. When the TK-
785 starts to receive data, the
icon is blinking.
7. If writing ends successfully, the LED on the TK-785 lights
and the checksum is displayed.
8. If you want to continue programming other TK-785, re-
peat steps 4 to 7.
Tuning
cable
Содержание TK-785
Страница 69: ...TK 785 TK 785 TK 785 BLOCK DIAGRAM K E 95 ...
Страница 70: ...TK 785 TK 785 TK 785 96 BLOCK DIAGRAM M ...