Kenwood TK-361SA, Руководство по обслуживанию, Страница: 3 / 42

TK-361SA
3
REALIGNMENT
1. Modes
User mode
PC mode
Self programming mode
Clone mode
PC test mode PC tuning mode
Data programming mode
Mode Function
User mode For normal use.
PC mode
Used for communication between the trans-
ceiver and PC.
Data programming
mode Used to read and write frequency data and
other features to and from the transceiver.
PC test mode
Used to check the transceiver using the PC.
This feature is included in the KPG-88D(M2).
Clone mode
Used to transfer programming data from one
transceiver to another.
Self programming
mode Used to program the transceiver without any
external programming device.
2. How to Enter Each Mode
Mode Operation
User mode Power ON
PC mode Received commands from PC
Clone mode [PTT]+[Side2]+Power ON (Two seconds)
Self programming
mode
[PTT]+[Side1]+Power ON (Two seconds)
3. Getting Acquainted
Speaker/
microphone
jacks
Antenna
Battery pack
(KNB-30A)
:
;
B
@
.
=
q
PTT (Push to Talk) switch
Press and hold, then speak into the microphone to trans-
mit.
w
Side 1 key
Super lock (default).
e
Side 2 key
Scan + Temporary delete (default)
r
Channel selector
Rotate to change the operating channel.
t
Power switch/Volume control
Turn clockwise to switch the power ON and counter-
clockwise to switch the power OFF. Rotate to adjust the
volume.
y
LED indicator
Indicates the transceiver status. Lights red while trans-
mitting, green while receiving, and fl ashes red when the
battery power is low while transmitting.
4. PC Mode
4-1. Preface
The transceiver is programmed by using a personal com-
puter, a programming interface (KPG-22/22A, USB adapter
(KCT-53U)) and programming software (KPG-88D(M2)).
The programming software can be used with a PC. Fig-
ure 1 shows the setup of a PC for programming.
4-2. Connection Procedure
1. Connect the transceiver to the personal computer with
the interface cable and USB adapter (when the interface
cable is KPG-22A, the KCT-53U can be used.).
Notes:
• You must install the KCT-53U driver in the computer to
used the USB adapter (KCT-53U).
• When using the USB adapter (KCT-53U) for the fi rst time,
plug the KCT-53U into a USB port on the computer with
the computer power ON.
2. When the POWER is switched on, user mode can be en-
tered immediately. When the PC sends a command, the
transceiver enters PC mode.
When data is transmitting from the transceiver, the red
LED lights.
When data is received by the transceiver, the green LED
lights.
Notes :
• The data stored in the personal computer must match
Model Name when it is written into EEPROM.
• Change the transceiver to PC mode, then attach the in-
terface cable.
4-3. KPG-22/KPG-22A Description
(PC programming interface cable : Option)
The KPG-22/22A is required to interface the transceiver
with the computer. It has a circuit in its D-sub connector
(KPG-22: 25-pin, KPG-22A: 9-pin) case that converts the RS-
232C logic level to the TTL level.
The KPG-22/22A connects the SP/MIC connector of the
transceiver to the RS-232C serial port of the computer.
4-4. KCT-53U Description (USB adapter : Option)
The KCT-53U is a cable which connects the KPG-22A to
a USB port on a computer.
When using the KCT-53U, install the supplied CD-ROM
(with driver software) in the computer. The KCT-53U driver
runs under Windows 2000 or XP.