Kenwood CK 600 Скачать руководство пользователя страница 39

Страница: 39 / 44

Fig. 8.12

5 - Adjusting of the minimum

of the oven burner

This needs to be done only for the oven
burner (the grill is a fixed capacity) by
acting on the thermostat in the following
way:

– turn on the burner by setting the tem-

perature knob on position 10

– remove the knob and unscrew the by-

pass screw (fig. 8.12) about three
times by passing a small flat screw-
driver (Ø 3 mm blade, 100 mm length)
through the panel opening

– re-fit the knob and let the oven heat up

for about 10 minutes, then bring the
knob to position 1 (minimum) to oper-
ate the thermostat by-pass

– after having removed the knob again

and being very careful not to turn the
tap rod, slowly screw the by-pass
screws “G” (fig. 8.12) until you obtain a
flame of 3-4 mm in height.

N.B. For G30/G31 the by-pass screw
must be fixed thoroughly.

Flame correct

Flame faulty in
primary air

Flame with excess
primary air

IMPORTANT
All intervention regarding installa-
tion maintenance and conversion
of the appliance must be fulfilled
with original factory parts.
The manufacturer declines any lia-
bility resulting from the non-com-
pliance of this obligation.

LUBRICATION OF THE GAS TAPS

If a tap becomes stiff, do not force;
contact your local Service Agent.

Flame Flame

Flame

faulty in

correct

with excess

primary air

long, yellow

clear

short and sharp

and

interior blue

too blue interior

trembling

cone

cone tending to

detach

CAUSE

air regulating

correct

air regulating

tube, too

distance of

tube, too

closed

the tube

open

Содержание CK 600













































Результаты поиска

Содержание CK 600

Отзывы:

Похожие инструкции для CK 600

Бренды по названию

Популярные бренды

Kenwood CK 600, Инструкция по использованию - Рекомендации по установке

Результаты поиска

Содержание CK 600

Отзывы:

Похожие инструкции для CK 600

Бренды по названию

Популярные бренды