Kenmore 153.321160 страница 20 Скачать руководство пользователя

Страница: 20 / 28

2. Remove (slide) the filter from the unit.

3. If you are replacing the filter skip to step 4. To clean the

filter use a vacuum with a hose attachment to remove any
dust or debris.

4. Place the new or cleaned filter into the water heater and

secure the filter to the shroud with the screw loosened earlier.

NOTE:

Use the guides/slots when inserting the filter into

the water heater.

5. Restore power to the water heater and press the power

button to turn the water heater on.

NOTE:

The water heater

will conduct a system diagnostic check prior to operation.

Inspection/Cleaning of the Condensate Drain
Pan & Condensate Drain Lines

IMPORTANT:

Before attempting to clean or replace the

condensate drain pan or lines press the power button to place
the water heater in Standby Mode and shut-off power to the
water heater at the circuit breaker/fuse box.

1. Remove the access panel (fan side) by loosening the screws

securing it to the unit.

2. Check the condensate drain pan and drain lines for any dirt or

debris that might interfere with proper drainage. Wipe out any
dirt or debris with a damp cloth.

3. Once the condensate drain pan and lines have been

inspected/cleaned, secure the access panel to the water
heater.

4. Restore power to the water heater and press

the power button to turn the water heater on.

NOTE:

The water heater will conduct a system diagnostic

check prior to operation.

Drain Valve Washer Replacement

NOTE: For replacement, use a 17/32” x 13/64” x 1/8” thick
washer available at your nearest hardware store.

• Before beginning turn “OFF” the electrical power supply to
the water heater.
• Follow

Draining

instructions. See

Draining

section.

• Turning counter clockwise, remove the hex cap below the

screw handle.

• Remove the washer and put the new one in place.
• Screw the handle and cap assembly back into the drain valve

and retighten using a wrench. DO NOT OVER TIGHTEN.

• Follow

Filling the Water Heater

instructions in the

Installation

Instructions

section.

• Check for leaks.
• Turn “ON” electric power to the water heater.

FIGURE 21.

Service

Before calling for repair service, read the

Start Up Conditions

and

Operational Conditions

found in the

Troubleshooting

section

of this manual.

If a condition persists or you are uncertain about the operation
of the water heater, let a qualified person check it out.

Contact Sears Repair Services at 1-800-4-MY-HOME

(1-800-469-4663).

Содержание 153.321160





























Результаты поиска

Содержание 153.321160

Отзывы:

Похожие инструкции для 153.321160

Бренды по названию

Популярные бренды

Kenmore 153.321160, Инструкция по использованию и уходу

Результаты поиска

Содержание 153.321160

Отзывы:

Похожие инструкции для 153.321160

Бренды по названию

Популярные бренды