Kendrion INTORQ BFK458-ATEX Скачать руководство пользователя страница 73

Страница: 73 / 81

Maintenance and repair

Kendrion INTORQ | BA 14.0217 | 07/2021

9.3.2

Checking the air gap

DANGER

Danger: rotating parts!

The motor must

not

run while the air gap is being checked.

1. Measure the air gap s

between the armature plate and the stator near the fastening screws using a

feeler gauge. (Refer to table Characteristics for air gap specifications, Page 23 for the values.)

2. Compare the measured air gap with the value for the max. permissible air gap s

Lmax

. (Refer to the

Characteristics for air gap specifications, Page 23 table for the values.)

3. Adjust the air gap to s

. (Refer to Adjusting the air gap, Page 74).

9.3.3

Release / voltage

DANGER

Danger: rotating parts!

The running rotor must not be touched.

DANGER

There is a risk of injury by electrical shock!

The live connections must not be touched.

1. Check the brake functionality when the drive is running: The armature plate must be tightened and the

rotor must move without residual torque.

2. Measure the DC voltage at the brake.

– Compare the measured voltage to the voltage specified on the name plate. A deviation of up to

10% is permitted.

– When using bridge/half-wave rectifiers: After switching to one-way voltage, the measured DC volt-

age may drop to 45% of the voltage specified on the name plate.

Содержание INTORQ BFK458-ATEX


















































































Результаты поиска

Содержание INTORQ BFK458-ATEX

Отзывы:

Похожие инструкции для INTORQ BFK458-ATEX

Бренды по названию

Популярные бренды

Kendrion INTORQ BFK458-ATEX, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание INTORQ BFK458-ATEX

Отзывы:

Похожие инструкции для INTORQ BFK458-ATEX

Бренды по названию

Популярные бренды