background image

16

Commissioning Procedure

Installed correctly  the  burner  should  not  emit  any 
fumes into the room. The following procedure  should be  
undertaken   to   test   that  the  unit  is  operating correctly.
1

After unit has been operating for a short  period a 

smoke match, smoke tube, carbon dioxide analyser

or similar should be directed  at the  top  opening of 
the unit.

2   This procedure  should be undertaken with the following 

conditions in the room:

• Open or closed windows
• Operation  of extraction/exhaust  fans, range hoods

etc

• Operation  of other  gas appliances
• Operation  of optional appliance fan at any speed.

3

Should any spillage be detected  the cause must be 

rectified before allowing commissioning of unit.

4.   Please test appliance operation before leaving.

2

Initially the Kemlan coal fire may burn with a 

slightly blue flame. After approximately 20 
minutes the fire will settle down and burn with a 
yellow flame.

3

As with all gas fires your gas coal/pebble or log

fire should  be  regularly serviced. We 

recommend  once each year. Service information
for an authorised person to follow has been set
out in attached leaflet.

4

PLEASE   NOTE:  Only  logs  provided  by  

Kemlan should be used with this appliance.

5

DO NOT place articles on or against this 

appliance.
DO  NOT  use or  store  flammable materials 
near this appliance.
DO  NOT  spray  aerosols  in  the  vicinity of  this

appliance whilst it is in operation.
DO NOT modify this appliance. Primarily a 
decorative appliance not  certified as a space 
heater.

6

The appliance is a live fuel effect product 

designed to operate with luminous flames and 
may exhibit slight carbon deposition.

7.

The guard is fitted to this appliance to reduce the

risk of fire or injury from burns and no part of it 
should be permanently removed.

SERVICE  - WARNING: ONLY TO  BE SERVICED  
BY AN AUTHORISED PERSON 

Warranty

Provided  the  appliance has  been  correctly  
installed according to instructions, Kemlan guarantee 
the cost of replacing parts and the labour in 
connection therewith for a period of 12 months from 
the date of installation.

User Instructions

1. WARNING NOTE: 

Properly installed and

operated this appliance will not leak gases. 

Persistent fume emission must not be tolerated.
If fume emission does exist, then the following 
immediate action should be taken.

A  Open doors and windows to ventilate room.
B  Turn the fire off.
C  Check for flue blockage and clear if necessary.
D  Do not attempt to relight the burner until the cause

of the emission has been identified and rectified. 
Should assistance be required contact nearest 
agent.

E  The gas burner  is designed to work in a Kemlan

Horizon electronic power flue ignition system. 

Working correctly there will be no spillage. Unit 
should cut out if not enough draw to ensure proper
functioning.

Installation Instructions Kemlan Power Flue Horizon Gas Fireplaces

Содержание Power Flue Horizon Gas Fireplaces























Отзывы: