background image

16  roof installation – evacuated tube collectors  

Kelvinator solar hot water systems

Roof installation –  

evacuated tube collectors

On the collector array inlet install a 1/2” to copper union 
onto the 1/2” male compression union fitting making sure to 
use a thread sealant.

1/2" female to 

copper union

1/2" male to 

collector union

copper support 

sleeve

Collector pipe work connections

Place the copper sleeve support into the inlet and outlet 
manifold pipes of the collector array. Install a 1/2" male 
compression union fitting (supplied with the collectors) and 
tighten the nut using two spanners as before, sealing the 
copper olive to the collector manifold pipes. 

collector

1/2" male 

compression 

union

Open the fittings kit KKSSURA and check that all 
components have been supplied (see components list). Since 
this kit is also used for flat panel type collectors there will be 
some pieces which will not be used.
On the collector array outlet install a tee piece, 1/2" to 3/8" 
reducing bush, vent valve, 1/2" nipple and 1/2" female to 
copper union (see diagram below). Between the fittings 
use a thread sealant that is capable of handling the high 
temperatures created by the collectors. Ensure the vent 
valve is installed so that its vent is pointing directly upwards, 
perpendicular to the ground (not the roof). 

vent valve

T-piece

1/2" female to 

copper union

1/2" male to 

collector union

1/2" to 3/8"  

reducing bush

1/2"nipple

Содержание KCT45036A

































Отзывы: