Keithley 7710 Скачать руководство пользователя

Страница: 26 / 28

Remote Model 7710 calibration

1. Connect the Model 7710 to the 7797 Calibration/Extender Board (see “

Extender board connections

”).

2. With the power off, install the Model 7710/7797 combination in Slot 1, and select the rear inputs with the

INPUTS switch. Allow three minutes for thermal equilibrium.

3. Accurately measure and record the cold temperature of the Model 7710 card surface at the center of the

card.

4. Press in and hold the Model 27xx OPEN key while turning on the power.

5. Enable calibration by sending the :CODE command. For example, the default command is:

CAL:PROT:CODE 'KI0027xx'

6.Initiate calibration by sending the following command:

CAL:PROT:CARD1:INIT

7. Calibrate the Model 7710 with the following command:

CAL:PROT:CARD1:STEP0 <temp>

Here <temp> is the cold calibration temperature (˚C) measured in Step 3.

8. Send the following commands to save calibration and lock out calibration:

CAL:PROT:CARD1:SAVE
CAL:PROT:CARD1:LOCK

Содержание 7710





























Результаты поиска

Содержание 7710

Отзывы:

Похожие инструкции для 7710

Бренды по названию

Популярные бренды

Keithley 7710, Руководство пользователя

Результаты поиска

Содержание 7710

Отзывы:

Похожие инструкции для 7710

Бренды по названию

Популярные бренды