Keithley 7710 Скачать руководство пользователя страница 13

Страница: 13 / 28

NumReadings = 1024

’ Take 1024 readings

Resp = Space$(80)

Cmd = Space$(80)

’ Configure the instrument for scanning DCV.

’

SendKI ("*RST")

' Put instrument in known state.

SendKI ("FORM:DATA ASCII

") ' Format data as an ASCII string.

SendKI ("FORM:ELEM READ")

' Return the reading with units only.

SendKI ("SAMP:COUN " + CStr(NumReadings))

' Take 1024 readings.

SendKI ("FUNC 'VOLT:DC', " + ScanList)

' Set function to DCV.

SendKI ("VOLT:RANG 100," + ScanList)

' Set Range to 100V.

SendKI ("VOLT:AVER:STAT OFF," + ScanList)

SendKI ("VOLT:DIG 4," + ScanList)

' Read to 4 significant digits.

SendKI ("VOLT:NPLC 0.002," + ScanList)

' Set NPLC to 0.002.

SendKI ("CALC3:OUTP OFF")

' Turn off limit test.

SendKI ("SYST:LSYN OFF")

' Turn off line-sync.

SendKI ("DISP:ENAB OFF")

' Turn off display.

SendKI ("SYST:AZER:STAT OFF")

' Turn off auto-zero.

SendKI ("CALC3:LIM1:STAT OFF," + ScanList)

' Turn off limits.

SendKI ("TRIG:DEL 0")

' Set trigger delay to 0 seconds.

SendKI ("TRAC:CLE")

' Clear reading buffer.

SendKI ("ROUT:SCAN " + ScanList)

' Set scan list.

SendKI ("ROUT:SCAN:LSEL INT")

' Initiate scan.

SendKI ("*OPC?")

' Determines if mainframe is ready.

Resp = QueryKI()

SendKI ("INIT")

' Initiate scan and store in buffer.

SendKI ("*OPC?")

Resp = QueryKI()

' Wait for scan to complete.

SendKI ("ROUT:SCAN:LSEL NONE;*OPC?")

' Stop scan.

Resp = QueryKI()

SendKI ("TRACE:DATA?")

' Get readings from buffer.

Resp = QueryKI()

Format_Readings (Resp)

SendKI ("DISP:ENAB ON")

' Turn display back on.

CloseWinsocket

' Disconnect connection to mainframe.

TestRunning = False

End Sub

Topics

Содержание 7710





























Результаты поиска

Содержание 7710

Отзывы:

Бренды по названию

Популярные бренды

Keithley 7710, Руководство пользователя

Результаты поиска

Содержание 7710

Отзывы:

Бренды по названию

Популярные бренды