Keithley 7710 Скачать руководство пользователя | Manualshive

Страница: 18 / 28

background image

14

Card connections

Screw terminals on the switching module are provided for connection to DUT and external circuitry.
The Model 7710 uses quick-disconnect terminal blocks. A terminal block can be wired outside the
module and then plugged back in. These terminal blocks are rated for 25 connect/disconnects.

WARNING

The information in this section is intended for qualified service personnel. Do
not attempt to perform this procedure unless qualified to do so.

shows how to access the screw terminals on the Model 7710. Channel designations for

the screw terminals are contained in

.

WARNING

Do not exceed the maximum specifications for the Model 7710 card. Refer to
the end of this User’s Guide for specifications.

Figure 4

Screw terminal access

UNLOCK

LOCK

Topics

Topics

Topics

«
...
16
17
18
19
20
...
»

Содержание 7710





























Отзывы:

Нет отзывов

Похожие инструкции для 7710

Бренд: IDEAL Страницы: 90

Бренд: SONS Online Systems Страницы: 11

Бренд: Kaise Страницы: 2

Бренд: CABAC Страницы: 23

Бренд: Geokon Страницы: 26

Бренд: GRASS VALLEY Страницы: 81

Бренд: Brymen Страницы: 11

Бренд: Brymen Страницы: 24

Бренд: Brymen Страницы: 24

Бренд: Brymen Страницы: 24

Бренд: Brymen Страницы: 20

Бренд: Amprobe Страницы: 70

Бренд: Amprobe Страницы: 68

Бренд: Steinberg Systems Страницы: 23

Бренд: UYIGAO Страницы: 21

Бренд: Harbor Freight Tools Страницы: 8

Бренд: koban Страницы: 76

Бренд: Retlux Страницы: 244

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды