manualshive.com logo in svg

Keithley 7710, Руководство пользователя

Поделиться
Скачать
Keithley 7710 Скачать руководство пользователя страница 25

21

Calibration

The following procedures calibrate the temperature sensors on the Model 7710 plug-in cards.

WARNING

The information in this section is intended only for qualified service person-
nel. Do not attempt these procedures unless you are qualified to do so.

Recommended test equipment

In order to calibrate the Model 7710, you will need equipment summarized in 

Table 3

.

Table 3

Recommended equipment for Model 7710 calibration

Extender board connections

The Model 7710 being calibrated should be connected to the 7797 Calibration/Extender Board, 
and the extender board should then be installed in scanner Slot #1. Note that the module being 
calibrated will be external to the Model 27xx to avoid card heating during calibration.

Model 7710 calibration

NOTE

Before calibrating the Model 7710, make sure that power has been removed from 
the card for at least two hours to allow card circuitry to cool down. After turning on 
the power during the calibration procedure, complete the procedure as quickly as 
possible to minimize card heating that could affect calibration accuracy. Allow the 
Model 27xx to warm up for at least two hours.

Front panel Model 7710 calibration

1. Connect the Model 7710 to the Model 7797 Calibration/Extender Board (see “

Extender board connec-

tions

” above).

2. With the power off, install the Model 7710/7797 combination in Slot 1 and select the rear inputs with the 

INPUTS switch. Allow three minutes for thermal equilibrium.

3. Accurately measure and record the cold temperature of the Model 7710 card surface at the center of the 

card with a digital thermometer.

4. Press in and hold the Model 27xx OPEN key while turning on the power.

5. Press SHIFT then TEST, and then display TEST:CALIB with the up or down range key. Press ENTER, 

select RUN, and then enter the appropriate calibration code (default: 0027xx).

6. With NEW CODE? displayed, use the up or down range key to display N, and then press ENTER.

7. Using the up or down range key, select CARD at the CAL:RUN prompt, and then press ENTER.

8. Set the display value to the cold calibration temperature (°C) you measured in Step 3, then press ENTER 

to complete Model 7710 calibration.

Digital Thermometer:

18 to 23˚C, ±0.1˚C

Keithley 7797 Calibration/Extender Board

Содержание 7710





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды