Keithley 7015-C Скачать руководство пользователя | Manualshive

Страница: 30 / 97

background image

Card Connections & Installation

3-3

Referring to Figure 3-1 for jumper locations, perform the fol-
lowing steps to install bank-to-bank jumpers:

1. If mated together, separate the relay card from the con-

nector card by removing the mounting screw and pulling
the two cards away from each other. Remember to han-
dle the cards only by the edges and shields to avoid con-
tamination.

2. Refer to Figure 3-2 and Table 3-1 to determine which

jumpers to install.

3. Using Figure 3-3 as a guide, install the jumpers on the

appropriate terminal pairs.

3.3.2 Backplane jumpers

The Model 7001 and Model 7002 mainframes have an ana-
log backplanes that allow the banks of a Model 7015 multi-
plexer to be internally connected to a compatible switching
card installed in another slot (see paragraph 2.4.1 for details).

The backplane jumpers for the multiplexer card assembly are
located on the relay card as shown in Figure 3-4, and Table
3-2 summarizes jumper connections. The card is shipped
from the factory with the jumpers installed.

Jumper removal

Perform the following steps to remove backplane jumpers:

Figure 3-3

Bank-to-bank jumper installation

Jumper

Jumper Terminal

Pair

1. If mated together, separate the relay card from the con-

nector card by removing the mounting screw and pulling
the two cards away from each other. Remember to han-
dle the cards only by the edges and shields to avoid con-
tamination.

2. Use Figure 3-4 and Table 3-2 to locate the jumpers that

are to be removed.

3. It is not necessary to unsolder the jumpers from the PC

board. Using a pair of wire cutters, cut both ends of each
jumper, then remove each cut jumper completely.

Jumper installation

Referring to Figure 3-4 for jumper locations, perform the fol-
lowing steps to install backplane row jumpers:

1. If mated together, separate the relay card from the con-

nector card by removing the mounting screw and pulling
the two cards away from each other. Remember to han-
dle the cards only by the edges and shields to avoid con-
tamination.

2. Physically remove a cut jumper by unsoldering the two

cut ends from the PC board.

3. Install a new #22 AWG jumper wire (Keithley P/N J-

15), and solder it to the PC board.

4. Remove the solder flux from the PC board. The cleaning

procedure is explained in paragraph 5.2.

Table 3-2

Backplane jumpers (on relay card)

Jumper*

Backplane connection

W100
W101
W102
W103
W104
W105
W106
W107

Bank A HI
Bank A LO
Bank B HI
Bank B LO
Bank C HI
Bank C LO
Bank D HI
Bank D LO

*See Figure 3-4 for location.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
28
29
30
31
32
...
»

Содержание 7015-C


































































































Отзывы:

Нет отзывов

Похожие инструкции для 7015-C

Бренд: Elenco Electronics Страницы: 15

Бренд: KJ Страницы: 26

Бренд: Circuit-test Страницы: 14

Бренд: CTC Union Страницы: 50

Бренд: Delta Страницы: 3

Бренд: APPA Страницы: 29

Бренд: Tenmars Страницы: 28

Бренд: Faithfull Страницы: 16

Бренд: Major tech Страницы: 16

Бренд: Chauvin Arnoux Страницы: 138

Бренд: Pyle Страницы: 2

Бренд: Meterman Страницы: 32

Бренд: Aktakom Страницы: 11

Бренд: Actisense Страницы: 19

Бренд: AXIOMET Страницы: 2

Бренд: Daiichi Electronics Страницы: 70

Бренд: Victor Страницы: 2

Бренд: Victor Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды