manualshive.com logo in svg

Keithley 7015-C, Инструкция по эксплуатации

Поделиться
Скачать
Keithley 7015-C Скачать руководство пользователя страница 28

 

3

 

Card Connections & Installation

 

3-1

 

3.1

Introduction

 

WARNING

The procedures in this section are in-
tended only for qualified service person-
nel. Do not perform these procedures
unless qualified to do so. Failure to rec-
ognize hazards and observe normal
safety precautions could result in per-
sonal injury or death. 

 

The information in this section is arranged as follows: 

 

3.2

Handling precautions:

 

 

 

Explains precautions that

must be followed to prevent contamination to the mul-
tiplexer card assembly. Contamination could degrade
the performance of the multiplexer card. 

 

3.3

Connections:

 

 

 

Covers the basics for connecting exter-

nal circuitry to the two available connector cards for
the multiplexer; the screw terminal connector card and
the multi-pin connector card. 

 

3.4

Typical connection schemes:

 

 

 

Provides some typical

connection schemes for single card, two-card and two-
mainframe system configurations. 

 

3.5

Model 7015 installation:

 

 

 

Provides a procedure to in-

stall the multiplexer card assembly in the Model 7001
or Model 7002 mainframe. 

 

3.2

Handling precautions

 

To maintain high-impedance isolation, care should be taken
when handling the relay card to avoid contamination from
such foreign materials as body oils. Such contamination can
substantially lower leakage resistances, thus degrading per-
formance.

To avoid possible contamination, always grasp the relay and
connector cards by the side edges or shields. Do not touch
the board surfaces, components, or areas adjacent to the elec-
trical contacts. Dirt build-up over a period of time is another
possible source of contamination. To avoid this problem, op-
erate the mainframe and multiplexer card in a clean environ-
ment. 

If a card becomes contaminated, it should be thoroughly
cleaned as explained in paragraph 5.2. 

 

3.3

Connections

 

This paragraph provides the basic information needed to
connect your external test circuitry to the multiplexer. It in-
cludes the installation of the bank-to-bank jumpers on the
connector card, installation/removal of backplane jumpers
on the relay card, and detailed information on making exter-
nal connections to the two available connector cards. 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 7015-C


































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды