Keiser Keiser 300 Скачать руководство пользователя страница 41

Страница: 41 / 46

LEG PRESS

CYLINDER ADJUSTMENT

NOTICE:

CYLINDERS ARE FACTORY-ADJUSTED AND REQUIRE NO

FURTHER ADJUSTMENT UNLESS THEY ARE REPLACED. Please contact

KEISER if you have any questions concerning adjustments or repairs.

Check the condition of the rubber crutch tips that the exercise arms against. These

must not be worn or damaged in any way. If they are worn replace them before

attempting to adjust a cylinder.

Adjust the left cylinder so that 7-9 threads are visible outside the jam nut (pg. 13

maintenance manual). Decrease the resistance all the way down and push the left

exercise arm all the way forward.

Push the right exercise arm all the way forward and engage the arm lock. Adjust the

right cylinder to make the lock work smoothly.

SPRING PINS

When installing the spring pin 3/16 X 7/8 (item # 23) into the foot pedal (item # 22),

line up the hole in the foot pedal with the hole in the foot pedal shaft (item # 25).

Drive the spring pin in until the end is 1/16” into the foot pedal.

Содержание Keiser 300















































Результаты поиска

Содержание Keiser 300

Отзывы:

Похожие инструкции для Keiser 300

Бренды по названию

Популярные бренды

Keiser Keiser 300, Руководство по запасным частям и обслуживанию

Результаты поиска

Содержание Keiser 300

Отзывы:

Похожие инструкции для Keiser 300

Бренды по названию

Популярные бренды