background image

KCU401-2 Keeler Cryomatic Service Manual  

 

 

 

 

9. Warranty

 

 

The 

Cryomatic and

 its components are covered by warranty that they meet their 

performance standards and are free from any defects in materials or workmanship. 
Within 12 months from delivery by Keeler, the manufacturer shall at no charge to the 
customer, upon written notice from the customer, repair or replace any components 
which are defective in material or workmanship.  
 
The customer agrees that it shall have no remedy in the event of any breach of the 
foregoing warranty other than as provided above. This warranty is exclusive and in 
lieu of all other warranties, expressed or implied, and all implied warranties of 
merchantability or fitness for a particular purpose are expressly disclaimed. 
 
The obligations of the manufacturer as set forth in this warranty are expressly 
conditioned on the following:- 
 
(i) No alterations or repairs of any malfunction of the system shall be made to the 
system except by the manufacturer or his authorized representative, without the prior 
written approval of the manufacturer or his authorized representative (and in no case 
will the manufacturer assume responsibility for repairs or alterations made by those 
other than the manufacturer or his authorized representative). 
 
And 
 
(ii) The customer shall give notice to the manufacturer or their authorized 
representative of any malfunction of the system and shall not use the system in any 
surgical operation after they are aware of any malfunction. 
 
(iii) The customer complies with manufacturer’s recommended Preventative 
Maintenance (see Section 8) and can provide proof of such action. 

 
 
 

10. Disposal

 

 
Ensure that this equipment is disposed of in accordance with local regulations. Please 
contact the supplier if in doubt. 

Содержание Cryomatic 2509-P-1000-JPN

























Отзывы: