Keba KeMes A100 Скачать руководство пользователя страница 11

Страница: 11 / 48

A100

Safety notes

Operating instructions V1.03

WARNING!

Danger due to lithium polymer batteries

This device contains rechargeable lithium polymer batteries

In the event that these instructions are not observed, the device can ex-
plode, fire may ignite and a formation of smoke may develop. Furthermore,
impaired function may result and safe operation cannot be ensured.

The device must never:

●

be disassembled or modified in any form

●

be exposed to heat or burned

●

be used when it is damaged

●

be operated with a power supply unit other than that specified

●

be pierced through with foreign objects (for example, nails), impacted or
kicked

●

be subjected to an impact load or sliding movement

●

be placed in a microwave device or a high-pressure vessel

●

be operated in an improper state (for example, with batteries that are be-
coming drained or in the event of a deformed enclosure).

CAUTION!

LASER RADIATION
DO NOT LOOK INTO THE BEAM
LASER CLASS 2

IEC 60825-1:2014
660 nm; 7 mW; pulsed

The laser beam must not be pointed at persons or animals. Avoid looking
into the direct or reflected laser beam.

The device must be switched off again after use. Ensure that it is not used
by unqualified personnel at any time.

2.4

Safety instructions for device maintenance

Caution

If this device is damaged, the device must be taken out of commission and
sent to our service partner for repair.

The device must not be opened.

Only the maintenance work expressly permitted by KEBA may be performed
(see Chap. "Maintenance").

Содержание KeMes A100

















































Результаты поиска

Содержание KeMes A100

Отзывы:

Похожие инструкции для KeMes A100

Бренды по названию

Популярные бренды

Keba KeMes A100, Руководство по эксплуатации

Результаты поиска

Содержание KeMes A100

Отзывы:

Похожие инструкции для KeMes A100

Бренды по названию

Популярные бренды