Keba KeMes A100 Скачать руководство пользователя страница 23

Страница: 23 / 48

A100

Operation and handling

Operating instructions V1.03

Main menu

(1st level)

Display

(2nd level)

Description

Menu 3/4
Settings

Menu 1/16
Format

Selection of the angle format

Format
---.--

(decimal degrees, default setting) or

Format
---°--'

(degrees / minutes)

Menu 2/16
Type

Selection of the type of the displayed angle.

Type

std

: Internal angle between the two measured legs

(default setting)
Type

sup

: Supplementary angle (180 ° - Internal angle

between the two measured legs)

Menu 3/16
Precision

Selection of the number of decimal places of the displayed
angle.

Precision --.--°: Display with 2 decimal places (default set-
ting)
Precision --.-°: Display with 1 decimal place

Menu 4/16
Log

Activation of data recording (on/off), default setting: off

Log
Off

Menu 5/16
Clock

Setting the real-time clock.

12.07.2018
09:36:39

Menu 6/16
AutoOff

Time for automatic switch-off from 1 to 30 minutes, default
setting: 5

AutoOff
5

Menu 7/16
Brightness

Adjusting the display brightness from 0 to 16, default set-
ting: 8

Brightness
8

Menu 8/16
MStartTrig

Mode for triggering the measurement in the

Machine

op-

erating mode (

move down

motion

). Default setting:

motion

move down

: the measurement starts as soon as the

pressure beam moves faster than the speed set using the

MSpeed

parameter.

motion

: the measurement starts as soon as the set sen-

sitivity of the

MSens

parameter has been exceeded.

Menu 9/16
MStopTrig

Mode for stopping the measurement in the

Machine

op-

erating mode (

move up

motion

). Default setting:

move up

move down

: the measurement stops as soon as the

pressure beam moves faster than the speed set using the

MSpeed

parameter and a constant angle is measured.

motion

: the measurement stops as soon as the set trip

limit of the

MSens

parameter has been exceeded and a

constant angle is measured.

Содержание KeMes A100

















































Результаты поиска

Содержание KeMes A100

Отзывы:

Похожие инструкции для KeMes A100

Бренды по названию

Популярные бренды

Keba KeMes A100, Руководство по эксплуатации

Результаты поиска

Содержание KeMes A100

Отзывы:

Похожие инструкции для KeMes A100

Бренды по названию

Популярные бренды