KEB COMBIVERT F5 Series, Инструкция по эксплуатации

Страница: 27 / 116

GB - 9
GB
2. Technical Data
2.1 Technical Data 230V Class
Technical Data
Site altitude max. 2000m. With site altitudes over 1000m a power reduction of 1% per 100m must be taken into
consideration.
The technical data is for 2/4-pole standard motors. With other pole numbers the inverter must be dimensioned onto the
motor rated current. Contact KEB for special or medium frequency motors.
1) With the regulated systems F5-M as well as F5-S 5% are to be subtracted as control reserve
2) This data is only valid for units with integrated PFC (see "unit identification")
3) Max. current before the responding of the OL2-function (only F5-M; F5-S; F5-A)
4) Recommended minimum cross section of the motor wire for rated power and a cable length of upto 100m (copper)
5) This data is only valid for units with internal brake transistor GTR 7 (see "unit identification")
6) At units with integrated filter (see "unit identification"):
up to max. 5m line length and 4kHz operating frequency = Limit Value B (EN 55011)
up to max. 10m line length and 16kHz operating frequency = Limit Value A (EN 55022)
05 07 09 10 12 13
A A B B D B D D E
1 1 3 1 1 3 1 3 1 3 1 3 1 3 3 3
[kVA] 0,9 1,6 2,8 4,0 6,6 9,5
[kW] 0,37 0,75 1,5 2,2 4,0 5,5
[A] 2,3 4 7 10 16,5 24
[A] 4,1 7,2 12,6 18 29,7 36
[A] 5,0 8,6 15,1 21,6 35,6 43
[A] 4,6 4,6 3,2 8,0 8,0 5,6 14 9,8 14 9,8 20 14 20 14 23 31
[A] – 3,7 – – 6,4 – – – – –
[kW] – 0,85 – – 1,5 – – – – –
[A] 10 16 10 20 16 20 16 20 16 25 20 25 20 25 35
[kHz] 4 16 8 16 16 8 16 8 8
[kHz] 4 16 8 16 16 16 16 16
[W] 30 55 65 90 130 105 170 210 290
[W] – 85 – – 130 – – – – –
[A] 2,3 4 7 10 16,5 24
[A] 2,3 4 7 10 16,5 24
[A] – 2,3 – 4 7 8,5 10 10 16,8
[°C] 90
[mm²] 1,5 1,5 2,5 1,5 2,5 1,5 2,5 1,5 4 2,5 4 2,5 4 6
[Ohm] 100 56 100 56 47 33 27 16
[Ohm] 180 180 100 68 33 27
[A] 4,5 7,5 4,5 7,5 9,5 12 15 25
1
[Nm] 0,5 1,2
50
B
Inverter Size
Housing size
Phases
Output nominal power
Max. rated motor power
Output nominal current
Max. short time current
1)
OC-tripping current
Nominal input current
Nominal input current
2)
Real input rated power
2)
Max. permissible mains fuse (inert)
Rated switching frequency
Max. switching frequency
Power loss at nominal operating
Power loss at rated operation
2)
Stall current at 4kHz
3)
Stall current at 8kHz
3)
Stall current at 16kHz
3)
Max. heat sink temperature TOH
Motor line cross section
4)
Min. braking resistor
5)
Typ. braking resistor
5)
Max. braking current
Overload curve (page appendex)
Tightening torque for terminals
Mains voltage
Mains frequency
Output voltage
Output frequency
Max.shielded motor line length at 4 kHz
6)
Max.shielded motor line length at 8 kHz
6)
Max.shielded motor line length at 16 kHz
6)
Storage temperature
Operating temperature
Model / protective system
Relative humidity
EMC tested according to
Vibration/Jolt according to
Climatic category
[V] 180...260 ±0 (230 V Nominal voltage)
[Hz] 50 / 60 +/- 2
[V]
3 x 0...U Mains (3 x 0...255V
2)
)
[Hz] see Control board
[m] 10 30 10 100 100
[m] 10 20 10 50 100
[m] - 10 - 20 40 100
[°C] -25...70 °C
[°C] -10...45 °C
IP20
max. 95% without condensation
EN 61800-3
Germanischer Lloyd; EN 50155
3K3 in accordance with EN 50178