manualshive.com logo in svg

KEB combicontrol PCC C5, Инструкция по эксплуатации, Страница: 23 / 32

Поделиться
Скачать
KEB combicontrol PCC C5 Скачать руководство пользователя страница 23

GB - 23

COMBICONTROL

6.3  Parameter description

6.3.1  Runtime and error monitoring

The ru-parameters serve for monitoring of the program flow.

ru.00

Status

Address 0200h

Program status

no prog

no program loaded

prog OK

program loaded

prog corrupt

program checksum error

Control status

run

Program runs

Stop

Program stopped

breakpoint

Program is on break point

Error status

err_cyctime

The adjusted cycle time was exceeded

err_watchdog The length of the last PLC cycle exceeded the 

maximum value, the PLC program was stopped.

ru.01

cycle time

Address 0201h

This parameter indicates the cycle time adjusted by the PLC program in milliseconds. 

This value is also used for the cycle time monitoring, a value of 0 ms means a free-run-

ning PLC program without cycle time monitoring.

ru.02

axis mode

Address 0202h

The parameter indicates the axis configuration adjusted by the PLC program. There is a 

differentiation between normal- and synchronous/cyclic operation.

ru.03

axis errors

Address 0203h

The parameter indicates the axes which did not respond. This can have been released by 

interruption of the cable to the axis or by switching off the axis. The value 0 means that all 

monitored axes are connected correctly.

ru.04

min. process time

Address 0204h

ru.05

max. process time

Address 0205h

ru.06

response time

Address 0206h

ru.07

process time

Address 0207h

ru.08

idle time

Address 0208h

The cycle time of a PLC program flow is composed of:
response time

Time of recognizing the new program cycle up to the call of the PLC 

program

process time

Time, when the PLC program as well as all accesses by CoDeSys 

and COMBIVIS are processed.

idle time

Remaining time up to the next program cycle.

Parameter ru.04 / ru.05 displays the minimum/maximum process time and can be reset 

by writing of any value.

Содержание combicontrol PCC C5

































Отзывы:

Нет отзывов