Keatec Energy T 3310UL Скачать руководство пользователя страница 11

Страница: 11 / 43

KE 4256-5492 Keatec T Series 10-20kVA PF1.0 208Vac with Internal Battery 7.0 Touch Screen Users Guide English 20181118

This manual is for qualified personnel only

Page 10

An unused battery must be recharged every 6 months. Temporarily connecting the

UPS to a suitable AC supply and activating it for the time required to recharge the

batteries.

CAUTION!

The highest altitude that UPS may work normally with a full load is 1500 meters.

The load capacity should be reduced when this UPS is installed at an altitude higher

than 1500 meters. Load coefficient equals max load at altitude divided by nominal

power of the UPS.

Altitude(m)

1500

2000 2500 3000 3500 4000 4500 5000

Load

coefficient

100% 95% 90% 85% 80% 75% 70% 65%

3.5

External Protective Devices

For safety, it is necessary to install an external circuit breaker at the input AC supply and another at

the battery. This chapter provides guidelines for authorized personnel and qualified installers -

knowledge of local wiring codes and laws is essential.

External Battery

The UPS and its associated batteries are protected against the effect of over-current through a DC

compatible thermo-magnetic circuit-breaker (or a set of fuses) located close to the battery.

UPS Output

Any external distribution board used for load distribution shall be fitted with protective devices that

protect the UPS from becoming overloaded

Over-Current

Protection devices shall be installed at the distribution panel of the incoming mains supply.

CAUTION! Select a thermo-magnetic circuit-breaker with an IEC 60947-2 trip

curve C (normal) for 125% of the current as listed below.

10kVA: 50A Input Circuit Breaker required.
15kVA: 63A Input Circuit Breaker required.
20kVA: 80A Input Circuit Breaker required.

3.6

Power Cables

The cable design shall comply with the voltages and currents provided in this section. Follow local

wiring codes and laws taking into consideration the environmental conditions (temperature and

physical).

WARNING!

Upon starting, ensure that you are aware of the location and operation of the

external isolators which are connected to the UPS input/bypass supply of the

mains distribution panel. Check to see if these supplies are electrically isolated.

Post any necessary warning signs to prevent any inadvertent operation.

For future expansion, it is recommended to install power cable according to the full rated capacity.

UPS

Cable Dimension

Содержание T 3310UL












































Результаты поиска

Содержание T 3310UL

Отзывы:

Похожие инструкции для T 3310UL

Бренды по названию

Популярные бренды

Keatec Energy T 3310UL, Руководство пользователя

Результаты поиска

Содержание T 3310UL

Отзывы:

Похожие инструкции для T 3310UL

Бренды по названию

Популярные бренды