Keatec Energy T 3310UL Скачать руководство пользователя страница 3

Страница: 3 / 43

KE 4256-5492 Keatec T Series 10-20kVA PF1.0 208Vac with Internal Battery 7.0 Touch Screen Users Guide English 20181118

This manual is for qualified personnel only

Page 2

Safety

Important safety instructions

SAVE THESE INSTRUCTIONS

- The instructions in this manual are deemed important and should

be closely followed at all times during installation and follow-up maintenance of the UPS and batteries.

Safety instructions in this manual act as a supplement to local safety codes and laws. Our company

does not assume any liability or responsibility caused by disobeying local safety codes and laws.

Before conducting any maintenance, repair, or shipment, first ensure that the UPS is turned off and

disconnected from all sources of internal and external energy

WARNING!

This UPS contains lethal voltages and high temperature inside. All repairs and service

should be performed by

AUTHORIZED AND QUALIFIED PERSONNEL ONLY

. Keep unauthorized

personnel away from UPS.

WARNING!

To reduce the risk of personal injury and equipment damage, abide by all local safety

codes and laws during operation, installation and maintenance.

WARNING!

To reduce the risk of electric shock, disconnect the UPS from the main supply before

installing a computer inter-face signal cable. Reconnect the power cord only after signaling

interconnections have been made.

WARNING!

(UPS having Internal Batteries): Risk of electrical shock – Hazardous live parts inside this

unit are energized from the battery supply even when the input AC power is disconnected.

WARNING!

(No User serviceable Parts): Risk of electrical shock, do not remove cover. No user

serviceable parts inside. Refer servicing to qualified service personnel.

WARNING!

(Non-isolated Battery supply): Risk of electric shock, battery circuit is not isolated from

AC input, hazardous voltage may exist between battery terminals and ground. Test before touching.

WARNING!

(Fuses): To reduce the risk of fire, replace only with the same type and size of fuse.

WARNING!

UPS units are extremely heavy. Caution should be taken in moving and positioning

equipment.

WARNING!

To reduce the risk of fire or electric shock, install the UPS in a temperature and humidity

controlled, indoor environment, free of conductive contaminants (flammable gas, excessive dust, etc.).

Ambient temperature must not exceed 40°C (104°F). Do not operate near water or in excessive

humidity (95% maximum).

WARNING!

To reduce the risk of overheating and fire, operate the UPS in a well-ventilated area.

WARNING!

To reduce the risk of fire or electric shock, output overcurrent protection and disconnect

switch must be installed in accordance with local Electrical Codes.

WARNING!

To reduce the risk of fire or electric shock, an external DC Circuit over current protective

device must be installed in accordance with the National Electric Code, ANSI/NFPA 70.

•

10kVA UPS connect only to a circuit provided with DC 63 amperes maximum branch circuit

over current protection in accordance with the National Electric Code, ANSI/NFPA 70.

•

15/20kVA UPS connect only to a circuit provided with DC 125 amperes maximum branch

circuit over current protection in accordance with the National Electric Code, ANSI/NFPA 70.

Содержание T 3310UL












































Результаты поиска

Содержание T 3310UL

Отзывы:

Похожие инструкции для T 3310UL

Бренды по названию

Популярные бренды

Keatec Energy T 3310UL, Руководство пользователя

Результаты поиска

Содержание T 3310UL

Отзывы:

Похожие инструкции для T 3310UL

Бренды по названию

Популярные бренды