8
安 裝 方 法
Preparation before installation
HOW TO INSTALL
安裝前
準
備
請 於固定佈 線 與本 產品 主機間 安 裝觸 點 開 距 不小 於
3 mm
的
“
電源全 極開 關
”(
規 格必 須 不低
於
250 V 13 A
)
及
~
漏電保 護開關
(
洩 漏電 流在
30 mA
以下
))。
電源全極開關
(
另購
)
固定佈線
Install an all-pole switch with the contact separation not less
than 3 mm and specifications not lower than 250 V 13 A
~
and a leakage protection switch (with the leakage current
lower than 30 mA) between the fixed wring and the main
body of this product.
All-pole switch
(Need to be purchased)
Leakage protection switch
(Need to be purchased)
Fixed wiring
Main body
of this
product
漏電保護開關
(
另購
)
本產品主機
1. Connecting power cord
電源線的連 接
Strand the core wire together after stripping,
then insert them into about 8 mm deep position
of the terminal block, ensuring that the part is
under the spring slice, and no copper core cord is
exposed outside. Make sure that the copper core
cords are fixed by screws reliably (the
.
recommended screw fixing torque is 0.49 N m)
(See Figure 2). Otherwise an electric shock may
be caused.
先將 剝線 後分散的 銅芯 線絞合在 一起
,
然後伸 入到 端 子
台約
8 mm
深 ,
並確保其 在 彈簧片的下 方
,
切勿出現 銅
線外 露現 象
。
螺釘 擰緊 後
,
請確 保銅 線不易鬆 脫(建議
.
螺釘 鎖緊 扭矩為
0.49 N m
)
,
否 則 可能會導致 觸 電
。
(右 圖
2
)
電源 線的 絕緣膠不 能破 損
,
否則 可能 會導致觸電或 短 路
。
剝線 長度
,
請按照 剝線 示 意圖(右圖
1
)進 行剝線
,
如 剝線
過長
,
可 能會導致 產品 短 路
。
電 源線請 選 用
60227
IEC 53
型絞 合 軟線
,
導 線的 截 面
2
積 為
3×1.5 mm
。
For the stripping length, please prepare
according to the wiring sketch (refer to figure 1).
If the stripping length is too long, it may cause
short circuit.
Do not damage the sheath of the power cord,
otherwise an electric shock or short circuit may
be caused .
Please select 60227
IEC 53 ordinary polyvinyl
chloride sheathed cord. Nominal cross-sectional
2
area of conductors is 3×1.5 mm .
警 告
WARNING
安裝和使用時禁止拆卸電路板蓋板
,
否則可能會導致觸
電或起火
。
To avoid electric shock or fire, do not remove the
PCB cover.
Wiring sketch
Terminal cutaway view
Conductor
Conductor
Insulation
Figure 2
Figure 1
Spring slice
Earth
Power cord
44
±
1
剝線示意圖
接線柱剝面圖
Unit
:
mm
單位
:
mm
電源線
接地引線
銅芯線
銅芯線
絕緣膠
彈簧片
圖
2
圖
1
安 裝 前 事 項
WORK BEFORE INSTALLATION