KBL megaSun 6700 a business Скачать руководство пользователя страница 9

Страница: 9 / 44

A s s e m b l y I n s t r u c t i o n s

6808 /7908

4.1 Tools and aids

Cutter knife

ISK screw driver (SW 4 / 60 mm)

Item no: 3410055251 (Accessories)

Standard Phillips screwdriver (PH2)

Screwdriver 3mm

Cordless screwdriver with PH2

& M6 ISK screwdriver bit

PH2

Hose clamps SW7 socket spanner

Side cutter

SW 19 pipe wrench

Item no.: 3410103500 (Accessories)

Spacer and protective padding e.g. timber

beams, foam strips and blankets.

Spirit level

SW 10 spanner

Reversible ratchet handle 1/4"

with AF socket SW13

2 (optimal 4) furniture trolleys

Tape rule or folding rule

PH2

Phillips screwdriver (PH2) 90° offset

Number of required persons

The disassembly and assembly steps of the tanning

device are described in the chapters that follow.

The tools and hardware required to correctly and

safely perform these steps are shown at the begin-

ning of each chapter.

If cable ties have to be removed during
disassembly, it is indicated by this sign
at the beginning of the chapter.

Cable ties which have been removed
during disassembly have to be replaced
during assembly.

4.2 Unpack tanning device and
accessories

4.2.1. UNPACK TANNING DEVICE

Remove plastic ﬁ lm and cardboard. Transport the

attachment parts to the installation site.

left

hand

side

right

hand

side

Exhaust air vent

ssembly

odule

- shoulder tanner (right)

AM - shoulder (left)

AM - canopy end caps (left/right)

Foot cladding (left/right)

AM - foot (left/right)

AM - hinge cap (left/right)

. Disassembly

Содержание megaSun 6700 a business













































Результаты поиска

Содержание megaSun 6700 a business

Отзывы:

Похожие инструкции для megaSun 6700 a business

Бренды по названию

Популярные бренды

KBL megaSun 6700 a business, Руководство по сборке

Результаты поиска

Содержание megaSun 6700 a business

Отзывы:

Похожие инструкции для megaSun 6700 a business

Бренды по названию

Популярные бренды