KBL megaSun 6700 a business Скачать руководство пользователя страница 40

Страница: 40 / 44

A s s e m b l y I n s t r u c t i o n s

6808 /7908

6. Connections & Initial operation

6.1 Connecting the mains
voltage

DANGER

Live parts

Risk of fatal injury due to electric shock

when touching live parts.

• Disconnect from mains and secure

against reconnection!

Both the power supply and the related connection

work must comply with national standards, e.g. those

set up by VDE in Germany. The connection work

must only be performed by qualiﬁ ed expert staff.

The connection to the 400 V mains must be protected

by fuses. Their speciﬁ cations are listed in the chapter

“Technical data”.

CONNECTION REQUIREMENTS

The electrical installation must be equipped with a

freely accessible all-pole disconnecting device in

accordance with the overvoltage category III. This

means that for full separation each pole must have a

contact gap according to the conditions of the over-

voltage category III.

A residual current-operated circuit breaker (RCD)

with short time delay is absolutely required. KBL AG

recommends the following type: KBL 3200 0770 00

(type (Typ ABB F 204 A - 40//0,03 AP-R).

Should the operation of the tanning unit cause any

interference in the power supply network, e.g. with

ripple-control systems (TRA), consult your power

supply company to have corresponding blocking

elements (audio frequency suppressors) installed.

6.2 Connecting an external
audio source

When connecting an external audio source (studio

music), pay attention to the correct polarity.

Содержание megaSun 6700 a business













































Результаты поиска

Содержание megaSun 6700 a business

Отзывы:

Похожие инструкции для megaSun 6700 a business

Бренды по названию

Популярные бренды

KBL megaSun 6700 a business, Руководство по сборке

Результаты поиска

Содержание megaSun 6700 a business

Отзывы:

Похожие инструкции для megaSun 6700 a business

Бренды по названию

Популярные бренды