background image

12

Installation

Designated 

porducts

Installation

Carefully read this manual before installing the IDU.

Installation Precautions

Warning

Please carry out the installation according to local standards.
Ask your local dealer or professionals to install the product.

This unit must be installed by professional technicians with relevant specialized knowledge. Users 

MAY NOT install the unit themselves; otherwise, faulty operations may cause the risks of fire, 

electrical shock, injury, or leakage, which could harm you or others or damage the air conditioner.

Never modify or repair the unit on your own.

Otherwise, a fire, electric shock, injury or water leakage may occur. Get your local dealer or a 

professional to do so.

Ensure that the residual current device (RCD) is installed.

The RCD must be installed. Failure to install it may result in electric shock.

When powering the unit, follow the regulations of the local electric company.

Make sure that the unit is grounded reliably in accordance with laws. If the grounding is not 

completed correctly, it may cause electrical shock.

When moving, disassembling or reinstalling the air conditioner, get the assistance of your 

local dealer or a professional.

If installed improperly, fire, electrical shock, injury, or water leakage may occur.

Use the optional accessories specified by our company.

The installation of these accessories must be carried out by professionals. Improper installation 

may cause fire, electrical shock, water leakage and other hazards.

Use only power cables and communication cables that meet specification requirements. 

Properly connect all the wiring to make sure that no external forces are acting on the 

terminal blocks, power cables and communication cables. Improper wiring or installation 

may cause a fire.
The air conditioner must be grounded. Check whether the earth line is securely connected 

or broken. Do not connect the ground line to gas cans, water piping, lightning rods or 

telephone earth lines.
The main power switch of the air conditioner should be put in a position that is out of the 

reach of children.

It should not be obstructed by flammable objects such as curtains.

Open flames are prohibited when refrigerant leaks are present.

If the air conditioner is not cooling/heating properly, this may be caused by a refrigerant leak. If 

this occurs, contact your local dealer or a professional. The refrigerant in the air conditioner is 

safe, and usually does not leak.

If there is refrigerant leakage in the room, it is easy for a fire to occur after contact with the 

heating units of the heater/electric stove/stove. Please disconnect the power supply of the air 

conditioner, extinguish the flames of appliances that produce a flame, and open the windows and 

doors of the room to allow ventilation and ensure that the concentration of refrigerant leakage 

in the room does not exceed a critical level; keep away from the leakage point, and contact the 

dealer or professional personnel. 

After the refrigerant leakage is repaired, do not start the product until the maintenance 

personnel confirms that the leakage is well repaired.

Qualification and Safety Regulation Requirements

1

Содержание KSEF-22 DN5.0





























































Отзывы: