background image

10

Operation

During self-cleaning, there may be a slight clicking sound for about 10 minutes, indicating that 

the IDU is freezing, which is normal.

When the IDU reaches the set temperature, the air conditioner controller automatically stops 

the compressor operation and switches to the fan only mode. When the room temperature rises 

(in cooling mode) or falls (in heating mode) to a certain level, the compressor is restarted and 

cooling or heating operation is resumed.

All IDUs in the same air conditioning system can only operate in the same mode, for example, 

cooling, heating or others. If IDUs are in different modes, a conflict will occur, making the system 

unable to start. Make sure that all the IDUs operate in the same mode.

For the same air conditioning system, if ODU operates in changeover mode, the main wired 

controller allows users to select modes supported by the IDUs, while the wired controller of a 

non-master IDU displays the icon of "No heating or cooling options". In this case, the mode 

setting is unavailable, and other IDUs operate in the same mode as the master IDU.

   During the heating operation of the heat pump type air conditioner, the air conditioner 

absorbs heat from the outdoor air and releases it to heat the indoor air. This is the heat pump 

heating principle of the air conditioner.

   When the heat pump runs in heating mode, the ODU blows out cold air, causing the outdoor 

temperature to drop. When the outdoor temperature is extremely low, the heating capability 

of the air conditioner drops gradually. You are advised to use other heating devices for 

heating.

   When the air conditioner is in "Auto", "Cool", "Dry", and "Heat" modes, it may emit a low 

continuous "hissing" sound, which is caused by the refrigerant flowing between the IDU and 

the ODU.

   A "hissing" sound may be heard for a short time after the air conditioner stops operation or 

during "defrosting", which is caused when the refrigerant stops flowing or changes its flow.

   When the air conditioner is in Cool mode or Dry mode, a small and continuous rustling sound 

can be heard, which is caused by the drain pump.

   When the air conditioner starts or stops running, you may hear a squeaking sound which is 

produced by the expansion or shrinkage of parts or surrounding aesthetic materials due to 

temperature change. The sound will disappear when the air conditioner is running normally.

"Self-cleaning" sound of icing

Switching from cooling/heating (not available for cooling only units) mode to fan only mode

Mode conflict

No heating or cooling options

In winter, the outdoor temperature is low, and heating effects may be decreased

The air conditioner makes low noise

Содержание KSEF-22 DN5.0





























































Отзывы: