KAYO MOTOR BULL 150 Скачать руководство пользователя

Страница: 33 / 99

3.3 Steering column and brake

system

With the vehicle on a sturdy flat surface hold
handlebar firmly and push up and down as it
shown in the picture. Check for rattles, shaking or

excessive play

If there is, check steering column, bearings,
and fastening parts.
Tighten any loose fasteners and replace
worn bearings or bushings.

With the vehicle on a sturdy flat surface. Turn the
handlebar slowly all the way left then all the way
right to check if it turns smoothly.

If it is rough, hard to turn or loose, check the wire
and cable routing, if there is no problem, check
steering rod, ball joints for damage or wear.

Note: the steering handlebar must be smooth,
accidents may occur due to lack of control

Clearance for front and rear handlebars

：

Operate the front handle bar to check the
brake effectiveness and movement of
handle bar
Check the clearance of handlebars

Содержание BULL 150




































































































Результаты поиска

Содержание BULL 150

Отзывы:

Похожие инструкции для BULL 150

Бренды по названию

Популярные бренды

KAYO MOTOR BULL 150, Руководство по обслуживанию

Результаты поиска

Содержание BULL 150

Отзывы:

Похожие инструкции для BULL 150

Бренды по названию

Популярные бренды