KAYO MOTOR BULL 150 Скачать руководство пользователя страница 69

Страница: 69 / 99

The oil seal is damaged

or the oil seal edge is

damage/worn/aged

Oil leakage is ineffective

Oil leakage from the oil

seal

Replace the oil seal

Right crankcase

cover

The right crankcase

cover is worn or cracked

Oil leakage form the

case cover

Repair or replace

the case cover

The gasket of right

crankcase is

broken

Oil leakage between

the case cover and

the case

Replace the gasket

Left crankcase

cover

The left crankcase cover

is worn or cracked

Oil leakage form the

case cover

Repair or replace

the case cover

The gasket of left

crankcase is

broken

Oil leakage between

the case cover and

the case

Replace the gasket

5.4.4Maintenance of Crankshaft Connecting Rod

Disassemble, assemble and maintain crankshaft connecting rod

Remove the fixing bolt of crankcase from its holding

place.

Содержание BULL 150




































































































Результаты поиска

Содержание BULL 150

Отзывы:

Бренды по названию

Популярные бренды

KAYO MOTOR BULL 150, Руководство по обслуживанию

Результаты поиска

Содержание BULL 150

Отзывы:

Бренды по названию

Популярные бренды