KAYO MOTOR BULL 150 Скачать руководство пользователя страница 28

Страница: 28 / 99

3 Regular

maintenance

and adjustment

Maintenance information…………………………………………………………………22

3.1 Maintenance circle……………………………………………………………………23

3.2 Way of maintenance……………………………………………………………………24

3.3 Steering column, brake system………………………………………………………27

3.4 Wheels…………………………………………………………………………………32

3.5 Suspension system……………………………………………………………………………34

3.6 Gear shift mechanism, fuel device………………………………………………………………35

3.7 Throttle inspection……………………………………………………………………………36

3.8 Gear display…………………………………………………………………………37

3.9 Light device……………………………………………………………………………37

Maintenance information

Operation cautions

Note



Do not run the engine in unventilated areas, exhaust contains carbon monoxide (CO) and
other toxic components.



Do not touch the engine or exhaust. Please wear long sleeves work clothes and gloves.



As gasoline is flammable and explosive. Pay attention to sparks as well as open flames.
Vaporized gasoline may explode, please choose well-ventilated sites when working with
fuel systems.

Note:

Being careful of drive system and rotating parts, tie up loose hair and clothing if possible

Note:

Keep the vehicle on a flat and stable place

Содержание BULL 150




































































































Результаты поиска

Содержание BULL 150

Отзывы:

Бренды по названию

Популярные бренды

KAYO MOTOR BULL 150, Руководство по обслуживанию

Результаты поиска

Содержание BULL 150

Отзывы:

Бренды по названию

Популярные бренды