KAYO MOTOR BULL 150 Скачать руководство пользователя страница 61

Страница: 61 / 99

The fixing nut is not

properly tightened

Air leakage between

the cylinder head and

cylinder

The engine starts hard or fails to

start. Insufficient engine output;

Engine speed changes during

idle run

Tighten the fixing nut

Spark plug

Improper clearance

between electrodes

Weak or no sparking

from the spark plug

electrodes

Oil leakage between the

cylinder and crankcase

Adjust electrode gap to

0.6~0.7mm

The spark plug electrodes

are joined by carbon

deposit

No sparking from the

spark plug electrodes

The engine starts hard or fails to

star

Remove the carbon

deposit between the

electrodes

Excessive carbon deposit

or oil dirt in the spark plug

Weak or no sparking

from the spark plug

electrodes

The engine starts hard or fails to

start. Insufficient engine output;

Engine speed changes during

idle run

Remove the carbon

deposit or oil dirt

The spark plug insulator is

damaged

Weak or no sparking

from the spark plug

electrodes

The engine starts hard or fails to

start. Insufficient engine output;

Engine speed changes during

idle run

Replace with a new

spark plug of the same

type

The spark plug is not

properly tightened

Air leakage between

the spark plug and

cylinder head

The engine starts hard or fails to

start. Engine speed changes

during idle run

Tighten the spark plug

Содержание BULL 150




































































































Результаты поиска

Содержание BULL 150

Отзывы:

Бренды по названию

Популярные бренды

KAYO MOTOR BULL 150, Руководство по обслуживанию

Результаты поиска

Содержание BULL 150

Отзывы:

Бренды по названию

Популярные бренды