KaVo HealOzone 2130 C Скачать руководство пользователя страница 49

Страница: 49 / 61

Instructions for use HealOzone 2130 C
7 Maintenance

7.2 Maintenance

7.2.2 Sensor/counter mode

Sensor mode

Sensor mode is the factory default. Sensor mode continuously checks the moisture

level and reports when the moisture level is too high and the desiccant is used up.

Treatment can continue after the desiccant is changed.

See also: 7.2.3 Replace desiccant, Page 48

Counter mode

Adverse environmental conditions and climatic influences can in certain circum‐

stances lead to frequent warnings regarding the moisture level.

If this should occur in rare instances, the user can change the counter mode.

The counter mode checks the operating hours (600 hours are programmed) and the

number of treatments (1000 treatments are programmed). If one of the programmed

values is exceeded, the warning message "Desiccant used up" appears

With this setting, the user can be sure that the device is fully functional without

exchanging the desiccant too early.

After the maximum operating hours or treatments are reached, the warning mes‐

sage "Desiccant used up" appears.

▶ Change desiccant.

See also: 7.2.3 Replace desiccant, Page 48

▶ Press SET button.

The device changes to the display "Ozone concentration can only be ensured once

the desiccant is changed."

▶ Press SET button.

The query "New desiccant" appears to confirm the desiccant change.

▶ Change the displayed value "No" to "Yes" with the PLUS and MINUS buttons.

▶ Press the SET button to confirm the desiccant change.

Note

If the desiccant change was not confirmed with "yes" in counting mode, the warning

message "Desiccant used up" appears after each treatment.

47/57

Содержание HealOzone 2130 C






























































Результаты поиска

Содержание HealOzone 2130 C

Отзывы:

Похожие инструкции для HealOzone 2130 C

Бренды по названию

Популярные бренды

KaVo HealOzone 2130 C, Инструкция по эксплуатации

Результаты поиска

Содержание HealOzone 2130 C

Отзывы:

Похожие инструкции для HealOzone 2130 C

Бренды по названию

Популярные бренды