background image

 

Operating Manual 

 

16 

Original Operating Manual

 

 

 

 

After 50h / every 500h thereafter 

 

Check screw connections: 

 

 

(2) on the sideshifter housing (3). 

 

(4) and washer (5) on the guide (6)  

 

(7) on the upper hooks (8). 

 

(9) on the lower hooks (10). 

 

(13) on the lower hooks (14). 

 

(15) on the lower intermediate element (16). 

 

on the fork safety retaining stops (1). 

 

Replace loose or damaged screws. Torque the screws as specified in Chapter 6.1 
General. 

 

 

Weekly 

 

Grease: 

 

Sliding pieces (11) by way of the greasing nipples (12). 

 

Sliding pieces (18) by way of the greasing nipples (19). 

 

Sliding pieces (20) by way of the greasing nipples (21). 

 

Supporting rollers on the lower hooks (22) as necessary. 

 

 

Every 200h 

 

Check wear on: 

 

Sliding pieces (11). 

 

Sliding pieces (18). 

 

Sliding pieces (20). 

 

Supporting rollers (22). 

 

 

 

As necessary 

 

Renew worn sliders (18) by removing the hooks (10). Remove the fork positioner in 
the reverse order to that described in section 4.1. Replace the sliders (18). During 
installation pay close attention that the sliders (18) are seated correctly. Then fit the 
fork positioner as described in section 4.1. 

 

Renew worn sliders (20) by removing the hydraulic lines from the cylinder (23) with 
the hydraulic system depressurised. Remove the nut (24). Lift the attachment using 
the lifting points marked. Replace the sliders (20). Ensure correct seating of the 
sliders (20) during installation. Reinstall the attachment and cylinder (23) with nut (24) 
and the hydraulic lines. 

Содержание T 400Z






















Отзывы: