manualshive.com logo in svg
background image

3

Installation requirements:

•  Read and understand all instructions and safety warnings prior to installation and use.

•  Equipment must be installed as required by the instructions.

•  Do not use this equipment outside of its intended purpose, or if site conditions would pose a dangerous installation.  

•  To be installed and operated only by an adult.  Not to be used by children.

•  Never install in areas where swimming is allowed or where people enter the water.  

•  Never use in a swimming pool.  

•  Do not use this equipment for intentional weed removal, sediment removal or dredging.  

•  Follow all local and national electrical wiring rules for the electrical circuit feeding this equipment.  Failure to comply may result 

in injury.  

•  All equipment must be powered from an RCD (residual current device) or GFCI (ground fault circuit interrupter) protected cir-

cuit.   

•  Do not modify any mounting hardware or guarding provided with this equipment.  All guarding purchased with a unit must be 

installed.

•  This equipment is intended to operate without interaction from personnel.  Never to be manipulated, moved, maintained, or ad-

justed while in operation.  Damage or injury could result.

•  The general public must be made aware of the installation and warned of the installation to prevent misuse or interference with 

the equipment.  

•  This equipment is intended to be used in water only.  The equipment should only be operated out of water if required to trouble-

shoot operation and during initial startup of the equipment.  The instructions provide detailed warnings and instructions for such 

activities and should only be performed by a trained person.

Unit Specs

Model

Voltage 

range

Operating 

amps

lock rotor 

amps

4400EJ

208-240

6.5@220V 20@220V

8400EJ

208-240

9.5@220V 40@220V

3.1EJ

208-240 13.2@220V 60@220V

2.3EJ

190

6.4

41

3.3EJ

190

10

69

5.3EJ

190

15.2

98

2.3EHJ

380

3.3

21

3.3EHJ

380

5

34

5.3EHJ

380

7.7

49

Utility requirements:  

The Electrical circuit must be provided to supply sufficient voltage and amperage to the unit.  These ratings are listed in the above 

table (unit specs).  This circuit must also include a disconnect means and short circuit protection.

Содержание 4400EJ
















Отзывы: