English
11
32
Suction hose
33
Spray / suction hose
34
Fresh water tank
35
Float switch
36
Wastewater container carrying handle
37
Wastewater container, removable
38
Float screw
39
Float
40
Filter casing
41
Flat fold filter
42
Quick Start Guide
43
Fluff filter
44
Cover seal
Control panel
Illustration C
1
0/OFF
2
Operating mode: Spraying
3
Operating mode: Vacuuming
4
Operating mode: Spray/Vacuum
5
Operating mode: Spraying/Vacuuming/Heating mode
6
Operating mode: Spraying/Heating mode
7
Operating mode: Heating mode
8
Turn switch
Start-up
1. Check the power cord, extension cable and hoses
for damage before each start-up.
Installing accessories
Illustration D
Illustration E
Illustration F
Mixing the cleaning solution
DANGER
Danger from detergents
Risk of injury and damage
Observe all instructions that are included with the deter-
gents used.
Note
Warm water (maximum 50 °C) increases the cleaning
effect. Check the temperature resistance of the surface
to be cleaned.
Note
Use detergents sparingly to conserve the environment.
1. Mix fresh water and detergent in a clean container
(concentration as specified for the detergent). Dis-
solve the detergent in the water.
Filling the fresh water tank
1. Remove the fresh water tank cap.
2. Fill the cleaning solution into the fresh water tank up
to the 1/1 marking (approx. 30 litres) of the filling lev-
el display.
3. Replace the cap of the fresh water tank.
Replacing the carpet adapter
1. Press the floor nozzle latch on one side.
2. Swing out and remove the carpet adapter.
3. Insert a new carpet adapter and engage the latch.
Operation
Working with accessories
Note
An additional power socket is provided for connecting
additional electrical devices.
DANGER
Danger of electric shock
Risk of injury and damage.
The socket is only intended for the direct connection of
the additional brush wash head PW 30/1 to the Puzzi
30/4 E. Any other use of the socket is prohibited.
Folding the push handle in/out
1. Release the push handle fastening screws and ad-
just the push handle.
Switching on the device
1. Connect the mains plug.
2. Set the turn switch to spray. Spray pump is switched
on.
3. Set the turn switch to vacuum. Suction turbine is
switched on.
4. Set the turn switch to spray/vacuum. The spray
pump and suction turbine are switched on.
5. Set the turn switch to spraying/vacuuming/heating
mode. Spray pump, suction turbine and heating are
switched on.
6. Set the turn switch to spray/heating mode. The
spray pump and heating are switched on.
7. Set the turn switch to heating mode. Heating is
switched on. In this operating mode, the cleaning
solution can be preheated or kept warm when work
is interrupted.
Cleaning mode
ATTENTION
Danger from cleaning solution
Risk of damage
Before using the device, check the object to be cleaned
for colour fastness and water resistance in an inconspic-
uous place.
Note
When the wastewater container is full, the suction air
flow is interrupted by the float.
1. Remove loose dirt from the object to be cleaned.
2. Press the lever on the angle piece to spray the
cleaning solution.
3. Run over the surface to be cleaned in overlapping
paths. Pull the nozzle backwards (do not push).
Switching off the device
1. Switch off the device by setting the turn switch to 0/
OFF.
2. Pull out the mains plug.
Unlocking the cover
1. Unlock the cover by folding up the carrying handle
of the wastewater container by 90°. The cover can
be opened.
Illustration G
Содержание Puzzi 30/4 E
