Kärcher KM 100/100 R LPG, Руководство пользователя

Страница: 23 / 269

-
5

Danger
Risk of injury and damage! Do not use a
forklift to unload the appliance.
To unload the machine, proceed as follows:

Cut plastic packing belt and remove foil.

Remove the elastic tape fasteners at
the stop points.

Four indicated floor boards of the pallet
are fastened with screws. Unscrew
these boards.

Place the boards on the edge of the pal-
let. Place the boards in such a way that
they lie in front of the four wheels of the
machine. Fasten the boards with
screws.

Slide the four support beams included
in the packaging under the ramp.

Remove the wooden blocks used for ar-
resting the wheels and slide them under
the ramp.

Danger
Risk of injury! Before engaging the free-
wheel operation, the machine must be se-
cured to prevent it rolling away.

Opening and securing cover

Engage freewheel lever in upper hole.
This blocks the travel drive function.

Close cover.
The machine can now be pushed.
Note
Do not move the machine for long distanc-
es without engaging self-propulsion, a
speed of 6 km/h should not be exceeded.

Engage freewheel lever in lower hole.
The travel drive is now ready for operation.

Close cover.
The appliance can now be driven.

Park the sweeper on an even surface.

Remove the key.
몇
Warning
Only use replacement cylinders with 11 kg
contents of tested models.

Danger
Risk of injury!
–
Follow safety regulations for LPG vehi-
cles.
–
Formation of crusts and yellow-frothing
deposits on the gas cylinder indicate
leakiness.
–
Cylinders must be changed only by in-
structed persons.
–
Cylinders containing propellant gases
must not be changed in garages and
underground areas.
–
Do not smoke and use uncovered light
while changing the cylinder.
–
While changing cylinders, first close the
locking valve of the LPG cylinder firmly
and immediately put the protective cap
on the empty cylinder.

Place the cylinder in such a way that the
connection threading of the locking
valve vertically points upwards.

Close the bracket closure.

Attach safety splint.

Remove protective lid (1) from the con-
nection valve of the cylinder.

Connect the gas tube with Union nut (2)
(use 30 mm spanner).
Note
Connection has a left threading.
몇
Warning
Open the gas drawing valve (3) only after
starting the appliance (refer chapter Start-
ing the appliance).
몇
Warning
Danger through escaping gas. Route/at-
tach the gas hose so that it does not pro-
trude outside the appliance and cannot be
torn off during operation.

Danger
Risk of explosion!
–
Only use the fuels specified in the Op-
erations Manual.
–
Do not refuel the machine in enclosed
spaces.
–
Smoking and naked flames are strictly
prohibited.
–
Ensure that no fuel reaches the hot
open surfaces.

Switch off engine.

Opening and securing cover

Check fuel level via the tank indicator.

Open fuel filler cap.

KM 100/100 R P: Use regular unleaded
petrol.

Fill tank to max. 1 cm below the lower
edge of the filler nozzle.

Wipe off any spilt fuel, remove funnel
and close fuel filler cap.

Close cover.

Pull seat adjustment lever inwards.

Slide seat, release lever and lock in
place.

Check that the seat is properly locked in
position by attempting to move it back-
wards and forwards.
1 Driving
Driving to the Place of Use.
2 Sweeping with sweep roller
Roller brush is lowered. The roller brush
and the side brush will rotate.
3 Sweeping with side brushes
Roller brush and side brushes are low-
ered.
Note
The machine is equipped with a seat con-
tact mat. If the driver's seat is vacated, the
appliance is switched off and the immobilis-
ing brake is activated automatically.

Opening and securing cover
Before Startup
Unloading
Moving sweeper without engaging
self-propulsion
Moving sweeper by engaging self-
propulsion
Start up
General notes
Connect/ change gas cylinder (only
KM 100/100 R LPG)
Fueling (KM 100/100 R P only)
Refuelling the machine
1
2
3
Operation
Adjusting driver's seat
Programme selection
Starting the machine
Open the fuel tap (KM 100/100 R P only)
22 EN