Kärcher ICC 2 Euro 3, Руководство пользователя

Страница: 36 / 308

36
English
Î Charge battery.
Î Screw in cell caps.

Danger
Risk of injury! Comply with safety regula-
tions on the handling of batteries. Observe
the directions provided by the manufacturer
of the charger.

Danger
Charge the battery only with an appropriate
charger.
Î Disconnect battery.
Î Connect positive terminal cable from
the charger to the positive pole connec-
tion on the battery.
Î Connect negative terminal cable from
the charger to the negative pole con-
nection on the battery.
Î Plug in mains connector and switch on
charger.
Î Charge battery using lowest possible
level of charging current.
Note
When the battery is charged, first remove
the charger from the mains and then dis-
connect it from the battery.
Î
Park the sweeper on an even surface.
Î
Connect air pressure testing device to
tyre valve.
Î Check air pressure and adjust if re-
quired.

Danger
When carrying out repairs on public high-
ways, wear warning clothing when working
close to passing traffic.

Danger
Risk of injury!
Î Park the sweeper on an even surface.
Î Remove ignition key.
Î Check stability of ground. Also secure
the machine with wheel chock(s) to pre-
vent it rolling away.
Î Lock parking brake.
Check tyres
Î Check tyre contact face for foreign ob-
jects.
Î Remove objects found.
Î Use suitable, commercially available
materials to carry out tyre repairs.
Note
Observe the manufacturer's recommenda-
tions. The journey may be resumed provid-
ing that the directions supplied by the
product manufacturer have been observed.
The tyre/wheel change should nonetheless
be carried out as soon as possible.
Intake point for the jack (front wheels)
Use the corresponding intake delivered
along with the vehicle.
Intake point for the jack (rear wheels)
Î Position vehicle jack at the appropriate
mounting point for the front or rear
wheel.
Î Loosen wheel nuts/ wheel bolts.
Î Raise machine using vehicle jack.
Î Remove wheel nuts/ wheel bolts.
Î Remove wheel.
Î Mount spare wheel.
Î Insert the wheel nuts/ wheel bolts.
Î Lower machine using vehicle jack.
Î Tighten the wheel nuts/ wheel bolts.
Note
Use a suitable commercially available vehi-
cle jack.

Danger
Risk of burns!
Î Allow engine to cool down.
Î Wait for at least 5 minutes after switch-
ing off the engine before checking the
engine oil fill level.
Î Raise waste container.
Î Pull out oil dipstick.
Î Wipe off oil dipstick and insert.
Î Pull out oil dipstick.
Î
Read the value of the oil level.
Î
Insert the oil dip again.
– The oil level must lie between “MIN“ and
“MAX“ marking.
– Add motor oil if the oil level is below the
"MIN" marking.
– Do not fill oil above the "MAX" marking.
Î Loosen the screw cap of the oil filling
opening.
Î Fill in motor oil.
Oil grade: see Technical Data
Î Close oil filler opening.
Î Wait at least 5 minutes.
Î Check engine oil level.

Danger
Risk of burns due to hot oil!
Î Ready a catch bin for appr. 6 litre oil.
Î Allow engine to cool down.
Î Unscrew oil drain plug.
Î Loosen the screw cap of the oil filling
opening.
Î Drain off oil.
Charging battery
Check the tyre pressure
Air pressure, front 3.75 bar
Air pressure, rear 4.75 bar
Replacing wheel
Tightening torque for front
tyres 140 Nm
Tightening torque for rear
tyres 120 Nm
Check engine oil level and top up, if re-
quired
Change the motor oil and the oil filter.