English
19
Î
Tighten wheel nuts.
몇
Warning
The engine is equipped with an oil deficien-
cy switch. When the fill level is insufficient,
the engine switches off and can only be re-
started once the engine oil has been replen-
ished.
Danger
Risk of burns!
Î
Allow engine to cool down.
Î
Wait for at least 5 minutes after switch-
ing off the engine before checking the
engine oil fill level.
Î
Open the device hood and secure it us-
ing the hood support.
1 Oil dipstick
2 Oil drain screw
3 Wing nut
4 Air filter
Î
Pull out oil dipstick.
Î
Wipe off the oil dipstick and insert until
the head of the oil dipstick rests on the
oil filler neck (see Fig. A).
Î
Pull out oil dipstick.
Î
Check engine oil level.
Î
If required, top up oil carefully.
Oil grade: see Technical Data
1 Left side part
2 Fastening screw for side part
Î
Open the device hood and secure it us-
ing the hood support.
Î
Unscrew all the 4 fastening screws of
the left side part.
Î
Remove the side part.
Î
Pull out oil dipstick.
Î
Keep a collection basin for old oil ready.
Î
Unscrew the oil drain screw and collect
used oil.
Î
Screw in oil drain plug.
Î
Fill in motor oil.
Oil grade: see Technical Data
Î
Close oil filler opening.
Î
Wait at least 5 minutes.
Î
Check engine oil level.
Î
Replace side part.
Î
Open the device hood and secure it us-
ing the hood support.
Î
Unscrew wing nut.
Î
Remove, check and clean filter car-
tridge.
Î
Use either a new or cleaned filter car-
tridge in the vacuum container.
Î
Screw on wing nut.
Î
Open the device hood and secure it us-
ing the hood support.
1 Spark plug
Î
Remove spark-plug connector.
Î
Unscrew and clean spark plug.
Î
Screw in cleaned or new spark plug.
Î
Push on spark-plug connector.
(1) Checking fill level
Î
Open the device hood and secure it us-
ing the hood support.
Î
Check the fill level in the header tank.
Note
The oil level must lie between the “MAX“
mark and a distance of 2 cm above the
base of the tank.
1 Equalising container
몇
Warning
This inspection may only be carried out
when the engine is warm
(2) Adjusting fill level
Î
Open the device hood and secure it us-
ing the hood support.
Î
Remove the lid of the container.
Î
If required, top up oil carefully.
Î
Close container.
Oil grade: see Technical Data
Danger
The engine requires approx. 3-4 seconds to
come to a standstill once it has been
switched off. During this time, stay well
clear of the working area.
Î
Turn ignition key to "0" and remove it.
Î
Open the device hood and secure it us-
ing the hood support.
Î
Remove covering lid.
Î
Check tension of drive belt and V-belt;
also check for wear or damage.
1 Screw
2 Belt tightener
Î
Loosen the screw, reset the belt tighten-
er and tighten the screw again.
Î
Replace covering lid.
Î
Open the device hood and secure it us-
ing the hood support.
Î
Check chain tension; the chain should
not deviate more than approx. 3...5 mm.
Î
Tighten the chain if the tolerance is
high:
1 Tightening pinion
Î
Loosen the tightening screw on the rear
side of the tightening pinion.
Î
Press down the tightening pinion and
fasten it with screws.
Î
Check the chain tension again.
Note
With model 1.183-901.0, the fine dust filter
is part of the scope of the delivery.
Î
Tilt the suction head upward.
Check engine oil level and top up, if re-
quired
Change the engine oil
Check air filter and replace, if necessary
Clean or replace the spark plug
Check and adjust hydraulic fluid fill level
and change oil – axle drive circuit
Checking drive belt
Check chain tension
Replacing the fine dust filter (option)
Содержание IC 15/240 W
