Kärcher HDS-C 9/15, Оригинальное руководство пользователя

Страница: 29 / 152

-
13
 Adjust the speed potentiometer in the
switching cabinet to the value that you
have ascertained (A).
Example: For a water hardness of 18 °dH
on the scale for the SB-HDS 9/15, set the
speed potentiometer to position 5.5. This
results in a pause of 27 seconds, i.e. the
solenoid valve will open briefly every 27
seconds.
 Close the switching cabinet.

The oil level must be between MIN and
MAX.

Cut off the top of the oil tank.
It is proposed to use the detergent contain-
er without cover. During transport, the con-
tainer can be closed using the delivered lid.
If the container should be kept closed dur-
ing operations, then make a hole of 25mm
diameter in the lid.
 Open the detergent container and fill in
detergent.
 Only HDS-C 7/11, HDS-C 9/15: Open
the fuel tank and fill in fuel.
1 Dosing container
 Remove the cover of the dosing con-
tainer and fill in RM 110.
 Close the lid again.
 Set main switch to “1”.
 Select cleaning programme 3.
 Set the switch for continuous opera-
tions/ coin verifier to continuous opera-
tions.
 Check burner setting. Rectify the burn-
er settings if the measured values devi-
ate from the values given below.
Note:
Upon completion of the examination, close
the system door and check the burner func-
tion with the system being completely
closed. If the burner goes out due to a lack
of air, the following measures can be taken:
–
Remove the stopper from the floor of
the plant.
– Partially remove the sealing on the door
sides. Also reduce the sealing starting
from the bottom until 20 to 30 cm.
 Set the continous operation/ coin verifi-
er switch to coin verifier (only for ABS
Münzprüfer).
We hereby declare that the machine de-
scribed below complies with the relevant
basic safety and health requirements of the
EU Directives, both in its basic design and
construction as well as in the version put
into circulation by us. This declaration shall
cease to be valid if the machine is modified
without our prior approval.
The signatories act on behalf of and with
the authority of the company management.
Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Straße 28-40
71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2018-01-19
Check the oil level
Preparing the detergent container
Filling in detergents
Fill in hardening liquid
Initial start-up HDS-C 7/11, HDS-C 9/
15
HDS-C 7/11 HDS-C 9/15
Fuel pressure,
approx. 1.1 MPa
(11 bar) 1.1 MPa
(11 bar)
Blower pres-
sure, approx. 2.5 hPa (2.5
mbar) 4.0 hPa (4.0
mbar)
CO
2
10...11% 10...11%
Emission tem-
perature 160...180
°C 180...200
°C
Emission loss max. 9% max. 9%
Soot values max. 1 max. 1
EU Declaration of Conformity
Product: High pressure cleaner
Type: 1.319-xxx
Relevant EU Directives
2000/14/EC
2006/42/EC (+2009/127/EC)
2014/30/EU
Applied harmonized standards
EN 60335–1
EN 60335–2–79
EN 55014–1: 2006+A1: 2009+A2: 2011
EN 55014–2: 1997 + A2: 2008
EN 61000–3–11: 2000
EN 61000–3–12: 2011
EN 62233: 2008
Applied conformity evaluation method
2000/14/EC: Appendix V
Sound power level dB(A)
HDS-C 7/11
Measured:
70
Guaranteed: 71
HDS-C 8/15
Measured:
70
Guaranteed: 71
HDS-C 9/15
Measured:
87
Guaranteed: 88
Chairman of the Board of Management Director Regulatory Affairs & Certification
29 EN