Kärcher BD 70/75 W Classic Bp, Руководство пользователя

Страница: 10 / 40

10 English
Maintenance-free batteries (AGM and gel batteries)
ATTENTION
Risk of damage from AGM and gel batteries!
Opening or drilling the battery housing will damage an AGM or
gel battery. It must then be replaced.
Do not open the battery housing and do not drill any holes.
Do not cover the pressure relief valve and do not change it.
1. Only charge AGM and gel batteries using the specified charg-
ers, see chapter: Charging the battery .
Installing and connecting batteries
몇
WARNING
Risk of injury due to the device tipping over!
Device may tip over when removing and installing batteries.
Ensure that the device is positioned stably when removing and in-
stalling the batteries.
ATTENTION
Risk of damage to the control electronics!
The control electronics can be destroyed by reversing the polarity
of the battery connections.
Take care to ensure the correct polarity when connecting the bat-
teries.
몇 WARNING
Danger to life from fire or explosion if batteries are deeply
discharged!
Incorrect charging of deeply discharged batteries can cause a
fire.
Do not start the device if the battery is deeply discharged.
Make sure that the battery is charged before starting the system.
1. Drain the waste water.
2. Pivot the waste water tank upwards.
3. Place the battery in the device as shown.
Important: Push the
batteries all the way back!
BD 80/100 and BR 85/100
Illustration K
170 Ah, 2.815-092.0
180 Ah, 2.815-101.0
240 Ah, 2.815-105.0
285 Ah, 2.815-095.0
1
Spacers
Illustration L
BD 70/75 and BR 75/75
115 Ah, 2.815-091.0
170 Ah, 2.815-092.0
180 Ah, 2.815-101.0
1
Spacers
2
Battery holder
3
Additional weights
4. Insert a spacer between the right batteries and the fresh water
tank,
a
for 115 Ah battery set: 1 piece lengthwise flat.
b for battery sets other than 115 Ah: 2 pieces lengthwise
upright on top of each other.
5. For BD 70/75 with 115 Ah battery set: Insert the 4 additional
weights.
6. Attach the battery fastener, to do so
a for BD 70/75: Install the 2 battery holders and for 115 Ah :
Tighten at the left and middle threaded holes. For BR 75/75
and BD 70/75: 170 Ah / 180 Ah: Tighten at the right and
middle threaded holes.
b For BD 80/100 and BR 85/100: Insert one or two spacers
flat lengthwise or vertically between the front batteries and
the fresh water tank so that the batteries cannot slip forward.
7. Connect the poles to the connection cables from the battery in-
stallation kit.
8. Clamp the connecting cables on the (+) and (-) battery termi-
nals that are still free.
9. Connect the device-side battery connector to the battery-side
battery connector.
10.Pivot the waste water tank downwards.
Removing the batteries
몇
WARNING
Risk of injury due to the device tipping over!
Device may tip over when removing and installing batteries.
Ensure that the device is positioned stably when removing and in-
stalling the batteries.
1. Turn the key-operated switch to "0" and remove the key.
2. Disconnect the battery plug.
3. Drain the waste water.
4. Pivot the waste water tank upwards.
5. Disconnect the device-end cable from the negative terminal of
the battery.
6. Disconnect the remaining cables from the batteries.
7.
For BD 80/100: Remove the spacer(s) between the front bat-
teries and the fresh water tank.
8. For 115 Ah battery set: Take out the additional weights.
9. Remove the batteries.
10.Dispose of the used batteries in accordance with statutory
provisions.
Initial startup
Charging the battery

DANGER
Risk of injury from charger!
Electric shock due to improper use of the charger!
Adhere to the mains voltage and fuse values specified on the de-
vice type plate.
Only use the charger in dry rooms with sufficient ventilation.
ATTENTION
Danger of explosion due to battery!
Gases accumulate under the tank during the charging process.
Pivot the waste water tank upwards before charging low-mainte-
nance batteries.
ATTENTION
Risk of damage due to unsuitable charger!
Do not connect the charger to the device-side battery connector.
Use only a charger suitable for the type of battery installed.
Read the operating instructions of the charger manufacturer and
observe the safety instructions in particular.
The average charging time is approx. 10-15 hours.
The device cannot be used during the charging process.
Note
The device has deep discharge protection, i.e. the brush motor
and turbine are switched off automatically when the permitted
minimum capacity level is reached.
1. Drive the device directly to the charger and do not drive on
slopes.
2. Pull out the device-side battery connector.
Illustration I
1
Battery plug, device side
2
Battery plug, battery side
3. Connect the battery-side battery connector to the charger.
4. Plug the mains plug of the charger into the socket.
5. Carry out the charging process in accordance with the operat-
ing instructions for the charger.
6. Connect the device-side battery connector to the battery-side
battery connector.
Battery set Capacity Charger
2.815-091.0 115 Ah 6654-367.0
2815-092.0 170 Ah 6654-436.0
2815-101.0 180 Ah 6654-434.0
2815-105.0 240 Ah 6654-437.0
2815-095.0 285 Ah 6654-419.0