DN1769-1809
5
Kantech Telephone Entry System Installation Manual
Australia, New Zealand (continued)
GENERAL WARNING
: The grant of a telepermit for any item of terminal equipment indicates only that Telecom
has accepted that the item complies with minimum conditions for connection to its network. It indicates no
endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no
assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a
different make or model, nor does it imply that any product is compatible with all of Telecom's network services.
IMPORTANT NOTICE
: Under power failure conditions, the KTES may not operate. Please ensure that a
separate telephone, not dependent on local power, is available for emergency use.
This equipment shall not be set up to make automatic calls to the Telecom "111" Emergency Service.
UL Compliance for the KTES-US and the KTES-CDN Models only
The Kantech Telephone Entry System (KTES) complies with the UL 294 which is described by the following: UL
Standard for Access Control Equipment, USA. The KTES enables users to grant access to the building, to their
visitors, via their own telephone line or cellular telephone. The KTES also supports basic schedule operations for
the postal lock supervision and automatic relay activation.
•
The KTES can be connected to the PC via IP or RS-485 or internal PTSN to the phone line, these are all
supplementary. The KTES must be connected to one of the compatible controllers (KT-300 or KT-400).
•
Use only a UL listed transformer available through Kantech distributors or dealers, please refer to the
Technical Support contact information to obtain the specific transformer, see page 2.
•
Kantech part number TR1640P/UL
(manufacturer part number Codex model SEP-1640U)
•
Kantech part number TR1640P/CSA
(manufacturer part number Codex model SEP/G-1640)
•
For UL 294:
•
Only models KTES-US (for installation in the USA) and KTES-CDN (for installation in Canada) are UL
listed.
•
If the KTES door lock output is used in fail-secure mode, a listed panic hardware device shall be used
to allow emergency exit from the protected area.
•
Electrical specifications, refer to
and
•
For class 1 installation, the optional camera need to be installed.
•
Each KTES will be battery backed up with a KT-BATT-12, 12V/7Ah battery.
•
The optional accessories allowed in a UL installation are:
•
Heater kit (part number KTES-HEAT)
•
Postal lock (part number KTES-POSTAL)
•
Color camera (part number KTES-CAM-N)
•
The KTES is an access control accessory.
•
Humidity test conducted at 90%.
•
Compatible card readers are: P225, P325, P600 and Polaris.
•
The KTES has an on-board capability of monitoring 4 input points. Each onboard input is supervised with
or without end-of-line resistors (5.6K ohm). The maximum distance of one line is 600 m (2,000 ft) with
AWG #22 in a single or double EOL configuration.
UL 294 Performance Levels
RoHS (Restriction on Hazardous Substances)
This standard restricts the use of the following substances: Lead, cadmium, mercury, chromium IV,
polybrominated biphenyl (PBB), and polybrominated diphenyl ether (PBDE) in electrical and electronic equipment
by no later than July 1, 2006.
Destructive
Attack
Line Security
Endurance
Standby
Power
KTES-US
Level I
Level I
Level IV
Level IV
KTES-CDN
Level I
Level I
Level IV
Level IV
KTES-OEM
Level I
Level I
Level IV
Level IV
Standby power achieved when 12 VDC, 7 Ah battery is used.
Содержание Telephone Entry System
