background image

DN1315-1007

2

KT-300 Door Controller Installation Manual

KT-300 Compliance Specifications

FCC & IC Compliance

This device complies with FCC Part 15, Subpart B:2009. Operation is subject to the following two conditions: (1) this device may 
not cause harmful interference, and (2) this device must accept any interference received including interference that may cause 
undesired operation. This class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment 
Regulations. The KT-300 is also compliant with EN55022:2006, Class B.

          Compliance Notice

This product is in conformity with EMC Directive 2004/108/EC based on results using harmonized standards in accordance with 
article 10(5) and LVD Directive 2006/95/EC based on results using harmonized standards. This product is labeled with CE mark 
as proof of compliance with the above mentioned European Directives.

CE & C-Tick Compliance

EN50133-1: Alarm systems - Access control systems for use in security applications: system requirements.

UL Compliance Notice

To comply with UL listings, the following requirements must be met:

Use of a UL listed computer

Use of UL listed readers (Wiegand 26 and 34 bits, mag stripe 26 and 34 bits, have been tested and found to comply)

Use of a UL recognized tamper switch on every housing cabinet for the KT-300

Do not use the SmartLink option

Use the Kantech IP Link Enhanced Ethernet Device

Us the KT3-LCD module on each KT-300 controller (should be installed near the controller)

Do not use a 220 V transformer (not UL listed)

Use only UL listed cables

Use only UL listed adaptors

Use only a UL listed transformer such as Kantech TR1640P/UL or DSC PRD1640

Use Kantech BD7-12 battery

The KT-CAB3000LDR and KT-CAB4000LDR have been evaluated by UL as alternate enclosures.

NOTE: 

Backup battery provides operation of up to 12 hours but has been tested only 4 hours per Section 33 of UL294, fifth 
edition.

NOTE: 

All circuits are power limited.

UL 1076 Standard:

The following Kantech readers were validated by UL for the UL 1076 standard: P225W26, P225KPW26, P225KPXSF, 
P225XSF, P325W26, P325KPW26, P325XSF, P325KPXSF, and P600. 

Содержание Door Controller Innovative and Powerful KT-300





























Отзывы: