background image

DN1315-1007

14

KT-300 Door Controller Installation Manual

KT-PC4204 - 4-Relay and Additional Power Supply Module

KT-PC4204 Introduction

The KT-PC4204 module is an output module with four 
programmable relays. This module can be used to “repower” the 
Combus. The KT-PC4204 can also be used for elevator control.

NOTE: 

Do not use any power supply other than the KT-PC4204 
module to repower the Combus. If a power supply other 
than the KT-PC4204 is used, the Combus repower 
function will not operate as intended. 

KT-PC4204 Specifications

Current draw: 30 mA (from Combus)

40 VA 16 VAC transformer required

Maximum 7 A/h battery required

Connects to the controller via 4-wire Combus

Four programmable relay contacts rated 2 A, 30 VDC

AUX current: 1.0 A max.

Tamper contact input

Can be used to repower the Combus

Unpacking the KT-PC4204

The KT-PC4204 package should include the following parts/items:

One KT-PC4204 circuit board

One ground wire assembly

Five plastic standoffs

One 5 A replacement fuse

Mounting the KT-PC4204

The KT-PC4204 should be located inside a compatible cabinet 
(Kantech part no. KT-4051CAB), mounted in a dry, secure 
location. Preferably, it should be placed at a convenient distance 
from the connected devices. Perform the following steps to mount 
the unit:

 1. Push the five plastic standoffs through the mounting 

holes on the back of the cabinet.

 2. Secure the cabinet to the wall in the desired location. Use appropriate wall anchors when securing the cabinet 

to dry wall, plaster, concrete, brick or other surfaces.

 3. Press the circuit board into the plastic standoffs to secure the module to the cabinet.

NOTE: 

Wiring may take place once the unit is mounted.

Installation and Wiring

Before wiring the unit, ensure that all power (AC transformer and battery) is disconnected from the KT-300 controller. Perform 
the following steps to complete wiring:

 1. Connect the four Combus wires to the KT-PC4204. Connect the red, black, yellow and green Combus wires to 

the RED, BLK, YEL and GRN terminal respectively.

 2. If the module is used for Combus Repower, 

connect the Combus wires according to the 
diagram on the right. Note that for this 
option, Jumper J1 must also be set to 
“Combus Relay”.

 3. Complete all output wiring.

 4. Connect the external tamper switch, if used.

Applying Power

After wiring is completed, apply power to the KT-300. Connect the battery leads to the battery, and connect the AC transformer. 
Then, connect power to the KT-PC4204; the battery leads followed by the AC transformer.

NOTE: 

Do not connect the power until all wiring is complete.

Assigning the KT-PC4204 Module

Содержание Door Controller Innovative and Powerful KT-300





























Отзывы: