![background image](http://html1.mh-extra.com/html/kambrook/kss600/kss600_instruction-booklet_3348570009.webp)
17
16
Tips For Steaming Curtains
• Wash and dry curtains as directed,
according to the fabric type.
• Hang the curtains and steam as they
are hanging in place.
• Place the steam iron softly against
the curtain fabric. Move the steamer
in a slow up and down motion,
focusing on major creases.
• Lightly stretch the curtain fabric with
one hand while steaming to assist in
removing creases.
Replacing the Anti-Scale
Cartridge
1.
When the cartridge replacement
reminder light illuminates, the steam
station will automatically stop
steaming until replaced.
2.
To replace the cartridge, press inwards
on the two tabs on the cartridge, and
pull the cartridge outwards and away
from the steam station. (See Fig. 3).
Fig. 3
3.
Replace the used anti-scale
cartridge with the reserve cartridge
included in the gift box, or to
purchase a replacement, visit
the retail outlet where the steam
station was purchased or contact
Kambrook Customer Care.
4.
Remove all packaging before fitting
into the steam station. Once the new
cartridge is fitted, plug the steam
station in and turn on at the power
point, then press the On/Off button
to power on. Press the replacement
cartridge reminder button on the
steam station body to reset the
counter.
5.
Use only the recommended
Kambrook anti-scale cartridge with
this steam station.
Activating the Self-clean
Function
NOTE:
Self-clean should be
carried out after every 10 uses.
Failing to do so may lead to
scaling and shorten the steam
station longevity
1.
Safely move the steam station
closer to a sink and connect to a
power point, making sure that the
steam station is not in the path of
the water to be released from the
iron.
2.
Ensure there is water in the tank
and turn the steam station on.
Wait until the iron is heated and
the ready light illuminates.
3.
Holding the steam iron horizontally
above the sink, press and hold
the steam control button for 6
seconds to activate the self-clean
function.
4.
The water pump will begin to
operate and self-clean will start
then automatically stop after
1 minute. The water pump will stop
when self-clean is complete.
5.
Once self-clean is completed,
continue to hold the steam
iron over the sink until no more
water droplets come out of the
soleplate. Sit the iron in the iron
rest to dry any residue water for
about 2 minutes.
6.
Turn off the steam station, unplug
and leave the steam iron to cool
completely.Wipe the cooled iron
soleplate with a damp cloth.
NOTE:
Before cleaning or storing,
always switch the steam station
off at the power outlet and then
remove the power plug from the
power outlet. Ensure the steam
station has cooled down before
cleaning or storing.
• Do not use harsh abrasive cleaning
agents or solvents.
• Do not place any part of the steam
station and steam iron in water or
any other liquid.
• Do not add any perfume, vinegar or
other chemicals to the water tank.
• Always empty the water tank after
each use. Never store with water still
in the tank.
• Always ensure the steam outlet holes
are clean, free from scaling and not
blocked.
Cleaning the Steam Station
Body & Soleplate
1.
To clean the outer surfaces of the
steam station and steam iron, wipe
with a damp cloth and allow to dry
before storing.
2.
To remove residue from the soleplate
which may have built up from
certain fabric finishes, clean with a
rough cloth that has been soaked
in a vinegar and water solution or
use commercial soleplate cleaner
to remove fabric residue. Dry
thoroughly after cleaning with a soft
cloth.
3.
To clean the steam holes between
self-clean, use a damp cloth to wipe
away build-up of lint or starch from
inside the steam holes.
Care, Cleaning & Storage
Using Your Steam Station
continued...