background image

42

EN

Clean and maintenance

● Before cleaning the air conditioner, please turn off the unit and disconnect power.

● Do not wash air conditioner with water. Otherwise, it may cause electric shock.

● Do not use volatile liquid (such as thinner or gas) to clean the air conditioner. 

Otherwise, it may cause electric shock.

Otherwise, it may damage the appearance of air conditioner.

Clean outer case: If there's dust on the surface of outer 

case, please use soft towel to wipe it. If the outer case

is very dirty (such as grease), please use neutral ablu-

Clean grille: Use cleaner or soft brush to clean it.

1. Remove the filter;

2. Clean filter

3. Install filter

a. Press the clasp as shown in the fig, and then remove the filter 1;

b. Pull out the filter 2.

Use cleaner or water to clean the filter. If the filter is very dirty (such as grease), 

use warm water 40

ºC

 (104

ºF

) melted with neutral abluent to clean it and then put 

at shady place to dry it.

After the filer is cleaned and dried, reinstall it well.

ent to wipe it. 

Warning:

● The filter should be cleaned about once every three months. If there's much dust
● Do not dry the filter with fire or hair drier. Otherwise, it may be deformed or catch 

Remove the heat-removal pipe from air conditioner, clean and dry it, and then rei-

nstall it. (For the method of installation and removal method, please refer to the 

instruction for Install and Remove Heat-removal Pipe).

in the operation environment, you can increase clean frequency.
fire.

Note:

Clean outer case and grille

Clean filter

Clean heat-removal pipe

filter 1

filter 2

clasp

Checking before use-season

Checking after use-season

1. Check whether air inlets and air outlets are blocked.

2. Check whether plug and socket are in good condition.

3. Check whether filter is clean.

4. Check whether batteries is installed in remote controller.

5. Check whether joint, window bracket and heat-removal pipe are installed tightly.

6. Check whether heat-removal pipe is damaged.

1. Disconnect power supply.
2. Clean filter and outer case.
3. Remove dust and sundries on the air conditioner.
4. Eliminate accumulated water in chassis (refer to the section of "discharge me-

thod" for details).

5. Check whether window bracket is damaged or not. If yes, please contact dealer.

Long-time storage

If you don't use the air conditioner for a long time, please maintain it by following

steps for good performance:

● 

Make sure there's no accumulated water in chassis and the heat-removal pipe is

● 

Pull out the plug and wrap the power cord.

● 

Clean the air conditioner and pack it well to prevent dust.

disassembled.

Notice for recovery

● 

Many packing materials are recyclable materials. Please deal with them through

● 

If you want to throw away the air conditioner, please contact local division or co-

local recycle bin.

nsultant service center for the correct disposal method.

Содержание KPC-09AI
































Отзывы: