background image

Easidew Plus Portable Hygrometer User’s Manual

4

  

 

97478 Issue 1, October 2014

Safety

The manufacturer has designed this equipment to be safe when operated using the procedures 

detailed in this manual. The user must not use this equipment for any other purpose than that 

stated. Do not apply values greater than the maximum value stated.

This manual contains operating and safety instructions, which must be followed to insure the safe 

operation and to maintain the equipment in a safe condition. The safety instructions are either 

warnings or cautions issued to protect the user and the equipment from injury or damage. Use 

qualified personnel and good engineering practice for all procedures in this manual. 

Electrical Safety

The instrument is designed to be completely safe when used with options and accessories supplied by 

the manufacturer for use with the instrument. The instrument is powered by an internally mounted 

rechargeable battery. The input power supply voltage limits for the battery charger supplied with the 

instrument are 90 to 264 V AC, 47/63 Hz.

NOTE: No other battery charger unit, other than that supplied with the instrument 

should be used.

NOTE: Do not allow the battery to fully discharge.

Pressure Safety

DO NOT permit pressures greater than the safe working pressure to be applied to the instrument. 

The specified safe working pressure is 4350 psig (300 barg). Refer to the Technical Specifications in 

Appendix A.

Toxic Materials

The use of hazardous materials in the construction of this instrument has been minimized. During 

normal operation it is not possible for the user to come into contact with any hazardous substance 

which might be employed in the construction of the instrument. Care should, however, be exercised 

during maintenance and the disposal of certain parts. 

Repair and Maintenance

The instrument must be maintained either by the manufacturer or an accredited service agent. Refer 

to www.kahn.com for details of Kahn Instruments’ worldwide offices contact information. 

Calibration

The recommended calibration interval for the Easidew Plus Portable Hygrometer is one year, unless 

otherwise specified by Kahn Instruments The instrument should be returned to Kahn Instruments. 

Содержание Easidew Plus

























Отзывы: