background image

The following measures also apply to machines not yet commissioned.

Please consult with KAESER if you have questions to the appropriate storage and commis‐

sioning.

1.

 Moisture and frost can damage the machine!

➤ Prevent ingress of moisture and formation of condensation.
➤ Maintain a storage temperature of  >32 °F.

2. Store the machine in a dry, frost-proof room.

12.4  Transport

12.4.1  Safety

Weight and center of gravity determine the most suitable method of transportation. The center of

gravity is shown in the drawing in chapter 13.2.

➤ Please consult with KAESER if you intend to transport the machine in freezing tempera‐

tures.

Precondition Transport only by forklift truck or lifting gear only by personnel trained in the safe transportation of

loads.

➤ Make sure the danger area is clear of personnel.

12.4.2  Transport with a forklift truck

Precondition The whole machine is over the forks.

Fig. 35 Transporting with a forklift truck

1.

 Machine damage caused by an unsecured enclosure.

➤ Prior to transporting, remove the enclosure and transport separately.

2. Drive the forks completely under the machine or palette and lift carefully.

12.4.3  Transport with a crane

Suitable lifting gear ensures correct transportation.

The sling bands must be fed under the machine.

The sling bands may not bear on the side of the machine enclosure.

12 Decommissioning, Storage and Transport

12.4 Transport

88

Operator Manual    Screw Compressor  
AIRTOWER 3C–7.5C Tri-Voltage

9_6917 34  USE

Содержание AIRTOWER 3C





























































































































Отзывы: