background image

Fig. 33 Changing the service unit

1

Service unit

2

Control module

3

Sensor

4

Sensor opening

5

Snap fastener

6

Condensate drain hose fitting

7

Contact spring

8

Condensate inlet

9

Shut-off valve

10

O-ring

11

Screw-in part

12

Sealing tape

13

Union nut with vent holes

14

Insulation

Removing the service unit

1.

 Serious injury or death can result from loosening or opening components under

pressure.
➤ Depressurize all pressurized components and enclosures.

2. Close the shut-off valve 

9

 upstream of the condensate drain.

3. Unscrew the drain hose fitting 

6

 at the condensate line.

4. Press the snap fastener 

5

 and carefully remove the control module 

2

 from the service unit 

1

.

5. Carefully loosen the union nut 

13

 at the shut-off valve 

9

 until remaining residual air has esca‐

ped through the venting holes.

6. Unscrew the screw-in part 

11

 from the service unit and place aside.

7. Remove the insulation 

14

 from the service unit.

Installing the service unit

Use only genuine KAESER service units to ensure correct function of the condensate drain.

Precondition Make sure the top of the service unit and the contact spring are clean and dry.

1. Fit the insulation 

14

 to the service unit 

1

.

10 Maintenance

10.17 Maintaining the refrigerated dryer

9_6917 34  USE

Operator Manual    Screw Compressor  
AIRTOWER 3C–7.5C Tri-Voltage

79

Содержание AIRTOWER 3C





























































































































Отзывы: